(800) 853-2651
SHOP NOW

Recent content by melonreo

Yesterday's Tractor Forums
  1. K

    New Idea 290

    I have a 9 ft New Idea 290 haybine. I need a new sickle bar. Almost impossible to find. Anyone have one? I'm in Southern Wisconsin. This post was edited by KenTennies on 07/02/2021 at 12:47 pm.
  2. D

    MF3165 hydraulic lift pump control lever

    Hello, I have a MF3165, and have been trying to get the 3-point hydraulics to work. I have a question about the control lever for the hydraulic lift pump (see picture). Is it supposed to move freely when the tractor is not running? It doesn't move at all, no matter how much pressure I put on...
  3. P

    IH 464 3 point stuck in top position

    Hi All Been following for a while. purchased my 464 earlier this year after it sat in a field for 7 years. Put a battery on it and new diesel with clean fuel filter and started right up. this is wear it went south. 3 point went all the way up and hydraulics went into dead head. was able to lift...
  4. Crazy Horse

    Spray paint bomb nozzles .... a survey ....

    After using a paint spray bomb, I usually try to follow the directions by turning the rattle can upside down and spraying the paint out of the nozzle tube until only the compressed air (or whatever it is) comes out (no paint coming out). Some guys never do that. Even with the proper way of...
  5. E

    Super C Fast Hitch wobble

    I purchased a 2 point fast hitch for $125 yesterday and notice lots of wobble behind the plates that attach to the rear end housing. Is there a common way to repair this. It appears to just be ware from years of use.
  6. S

    Farmall 460 Hydraulic Valves

    Just found out I need to change my PTO so I am putting a to do list together for that project. If anyone can think of anything else I need to do the same time I change my PTO, let me know. I'm also looking to tear down my 3 hydraulic valves- the middle isn't working. Any tips from anyone...
  7. N

    Ford 9600 Backhoe???????

    I have found a pretty good deal on an old Ford 9600, 1973. I was wondering if it is possible to attach a backhoe to an old tractor like that? The tractor is huge, 135 hp. Just not sure if anyone has done it or if it goes on like any standard 3 point. I have never owned a tractor so any help...
  8. R

    JD A

    I have a 1946 JD styled A, last summer i changed the oil in engine and took out quite a bit of water, now in the winter time i always turn it over so the cyc. don't seize up, so it's possible that i broke the connector from the oil pump, but now it has no oil pressure. ? when i changed the oil...
  9. M

    Determining Liquid Ballast

    Ford 2000; 3 cyl. Diesel; 8/2 Trans.....In checking the rear ag tires on my new-to-me tractor, I got a squirt of liquid out of the valve stem that looked a bit green and had no obvious odor. I suspect radiator coolant and water but was wondering what the smell/feel of calcium cloride is like...
  10. H

    1500 Diesel Issues

    I am helping a friend with a 1500 tractor with a 2 cylinder Shibuara diesel engine. The owner originally told me that the tractor ran but would not handle a load. I guess the tractor had sat for a few years but they recently took it to a shop to change the fuel, clean the tank, install a new...
  11. J

    Steering Arm

    Having trouble removing the steering arm from the gearbox of 1955 International 100 Farmall. There is no room to insert wheel puller teeth on the arm. Thoughts appreciated. I posted a short video. https://youtu.be/TkREuSj-9RY
  12. F

    Cage Free Egg

    Went to visit sons in college over the weekend took them out to eat. Looking at the menu board of this politically-correct restaurant, the soup I wanted had "Cage Free Egg' in it. My turn, I stepped up, ordered my soup and said "But I'd like my egg raised in a cage, please..." All my family...
  13. D

    Seat Cushions

    Anyone have a good place to send the warn out seats to get recovered now that Speer Cushion is out of business?
  14. B

    International 660 stuck in gear

    Have any of you guys had a 660 get caught between gears? Tractor ran fine one day the next not, seems to be caught between forward and reverse. I can only start tractor with clutch pushed in, as soon as I try to let it out its in reverse although I can move it to forward but cannot get it to...
  15. L

    Welded Sculptures

    Some may have heard of this artist, John Lopez. Was looking through his site and man am I impressed. Art, scrap metal, welding, & subject matter. Take a looksee http://www.johnlopezstudio.com!
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top