(800) 853-2651
SHOP NOW

Recent content by MF Pain

Yesterday's Tractor Forums
  1. M

    MF3080 gearbox

    Hi all, I have a Massey 3080 16 speed with Speedshift trans that is not engaging the low range reverse. Forward is fine but reverse will not engage and hold in. I have the Selector cover off and there are no obviously worn parts that I can see. There is a hydraulic component in the cover that I...
  2. M

    Agco parts books

    There must be so many different variants. My steering has two draglinks that go back to the steering box, one on each side and there is a valve on the steering box input shaft that controls the hydraulic cylinders.
  3. M

    Agco parts books

    Thanks Jim, unfortunately the link doesnt work for me. The parts diagram looks to be fairly similar but my machine has a cast front axle and no tie rod. The power steering has an hydraulic ram on each side that connects to the king pin spindles. All said and done all I need is to pull it down...
  4. M

    Agco parts books

    My machine is a MF40A Industrial Backhoe/Loader
  5. M

    Agco parts books

    I have obtained a login from my local dealer to the Agco parts books but cannot find any for the Industrial range. Do you get access to the Industrials in the US? Im after the parts view of the front axle pivot area if anyone can help. Thanks
  6. M

    MF40A Industrial front axle pivot

    I have a MF40A Industrial Backhoe Loader that is badly worn in the front axle pivot. Any advice on removal and repair much appreciated.
  7. M

    MF 3080 A B reverse

    I have a MF 3080 and am having trouble engaging reverse in A range. Forward engages correctly but when engaging reverse it is as though it is not throwing in far enough. Sometimes almost engages and then grinds without engaging. Linkages all appear OK - nothing loose or badly worn. Thanks for...
  8. M

    IH 444 British hydraulics

    Thanks Jim
  9. M

    IH 444 British hydraulics

    Hi all, I have a British IH 444, issue is the hydraulic valve in front of seat has had the shaft broken/screwed off. This is I think the tap to change from linkage to remotes? What is involved in fixing this. I do not have a manual yet but have one in the pipeline. Thanks for any help. Cheers Bill
  10. M

    MF40A industrial tie rod ends

    My MF40A backhoe/loader needs new tie rod ends. They are welded to the power steering cylinder rods. Any knowledge on how to replace them? Not sure if the cup is designed to press out of the end. Thanks
  11. M

    MF40A hydraulic oil

    Yes I am only talking about the loader and backhoe hydraulic oil.
  12. M

    MF40A hydraulic oil

    Hi all, I have a MF40A industrial loader/backhoe. It has always run ATF in the hydraulics but I would like to change this to the same oil I use in my other tractors rear ends that also supply the hydraulic systems on these tractors , namely 15W40 engine oil suitable for hydraulics as well...
  13. M

    David P on Nuffields?

    Hi Matt, The pump timing is as advanced as the slotted coupling will allow just to get the marks lined up so cannot advance any further unless it is possible to move the coupling on the drive side. Also with regard to the pages you have scanned I am having trouble reading the print - if your...
  14. M

    Simms pump on Nuffield

    Hi all, Well I think I have found the problem - it looks as though the coupling on the injector pump drive slipped when the engine over revved. Apart from resetting the timing I have not as yet reassembled and tested. A pic of the timing cover removed to remind me how much more work I have...
  15. M

    David P on Nuffields?

    Hi all, Well I think I have found the problem - it looks as though the coupling on the injector pump drive slipped when the engine over revved. Apart from resetting the timing I have not as yet reassembled and tested. A pic of the timing cover removed to remind me how much more work I have done...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top