(800) 853-2651
SHOP NOW

Recent content by motorstuff52

Yesterday's Tractor Forums
  1. M

    Gassing gohpers

    What are you squirting in the carb to make the smoke? Do the moles or gophers try and escape or do they stay in the hole?
  2. M

    Gassing gohpers

    Thanks to all for help. I can't speak for the gophers but I doubt they will thank you. Mike
  3. M

    Gassing gohpers

    The pocket gophers are digging up our farmyard worse than usual. I am thinking about using a flexible metal exhaust pipe on the 8N to gas the gophers with carbon monoxide. Has anyone had any luck doing this? I am also concerned if it will hurt the tractor. Will the back pressure hurt the...
  4. M

    pull type rotary cutter

    Another question: the reverse is pretty fast on our 8N. Does that become problem when using arotary cutter?
  5. M

    pull type rotary cutter

    Thanks to all who replied with the good advice. One option is a used 60 inch Bush Hog Squealer 3 point cutter, which I think weights about 630 pounds. Would the 8N handle this OK?
  6. M

    pull type rotary cutter

    Hi, I am thinking about getting a pull type 5 foot rotary cutter for our 8N. I am thinking about a pull type cutter as I have read that the front end can get a light with a 3 point mount rotary cutter. I would like to hear from someone who has used a pull type and how well it works. Also...
  7. M

    removing front pully nut IHC 460

    El Toro, Thanks for the help!
  8. M

    removing front pully nut IHC 460

    We are installing an engine from a 460 Farmall into a 460 Industrial tractor and need to remove the front pulley nuts from both engines in order to change the front engine mounting. So far, we have not had much luck removing the nut from either engine. We are going to find a 3/4 inch impact to...
  9. M

    Will an 8N handle a 6.5' King Kutter disc?

    Thanks all. Help is appreciated.
  10. M

    Will an 8N handle a 6.5' King Kutter disc?

    OOPs, I meant 5 or 6 feet wide, not 5 or 6 inches wide.
  11. M

    Will an 8N handle a 6.5' King Kutter disc?

    Thank you for the replies. Am I correct that the Dearborn discs sold for the 8N were either 5" or 6" wide?
  12. M

    Will an 8N handle a 6.5' King Kutter disc?

    We are looking at a 6.5" King Kutter angle frame disc with 16" discs to keep the weeds down in the trees and yard. It weights 540 lbs. Is this a good size for the 8N or should we look for a larger or smaller unit? I see the reviews for durability are not the best on this disc. Any comments...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top