(800) 853-2651
SHOP NOW

Recent content by Mpuller

Yesterday's Tractor Forums
  1. G

    John Deere M Final Drive assembly

    Can anyone give me advice on assembling the final drive and brake assembly on a 1948 JD M I am planning to reuse the bearings, they look good. Is that a good idea. Any tips on brake adjustment? Any help is appreciated. Thank you!!
  2. M

    East Tn Rumor

    It's A what?
  3. M

    TRIPLE CROWN OF CENTRTAL FLORIDA TRACTOR PULLS

    Mike, If they don't want to come don't try to stop them.
  4. M

    A question with never the same answer for enybody and eve...

    rich, what you say is true. Back in the day I ran A's, 50,60, & 70/720 diesels. Mostly green now, but deere was really overdue in moving to 4/6 engines, just like they were 30 yrs late in going to rotary binders.
  5. M

    A question with never the same answer for enybody and eve...

    supermpuller wrote: Remember JD said nobody need over 2 cylinders . And some still argue that deere should not have abandoned the obsolete 2 bangers.
  6. M

    Tractor Pull - September 12 - Lexington, SC

    Bulldog, That's OK. Can't get by the purple moline anyway.
  7. M

    Edmund, SC

    Hey Bulldog, you 'bout ready to pull next weekend? Better leave Eric home, he's gotten too tough for me to handle with that SM lately. www.edmundantiquetractorpull.com
  8. M

    Just a Quickie

    test
  9. M

    815 V8 motor

    my mistake! The 304/345 gas were V-8. Wasn't thinking too clearly. Had trucks with both, but never saw one in the combine.
  10. M

    815 V8 motor

    The 815 combine never came with a V-8. They came with either 304/345 gas or 407/414 diesel. The ones I had were 414 diesels.
  11. M

    I screwed up again...help!

    With #1 @ TDC on compression, adjust 1, 2, 3, & 5. Rotate 360 degrees, then adjust 4, 6, 7, & 8.
  12. M

    5000 series

    correction: 6430 & 6230.
  13. M

    5000 series

    buick/deere, looked @ 5ooo series, but got a 6430 @ 6230 to get the closed system & the triple wet clutch. What's your take on these?
  14. M

    Explain top vs. full cut tires

    SuperH, 71/2 & 12 mph classes full cuts are a must. Never seen full cuts alowed in 3 mph class, but I don't think they'd help there.
  15. M

    D-19 turbo charged whining

    Jim, As JHH said the D19 diesel was factory turboed 1961-1964, probably too new for some clubs.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top