(800) 853-2651
SHOP NOW

Recent content by mtny

Yesterday's Tractor Forums
  1. M

    2021.......

    Kinda strange I haven't seen major movement in steel prices yet out here in south central ny . Last coil of galvanized was up 8 cents a lb . Just priced 4800 lbs of beams and channel not much different from a month ago .
  2. M

    Looking for ideas

    No pics but I tack welded 1/2" conduit together . Zip tied cheap lights to it . Hardly weighed any thing .
  3. M

    Unstacked Hay

    I was usually a one man show . Had a setup I could drop 6-700 in without stopping . I'd go in and stack the next day or whenever had time . The last year I did it a couple neighbor kids would come in and stack when they had a chance . Worked out good . I did run a new Holland bale wagon .
  4. M

    Strange welding rod

    Are you sure it wasn't galvanized angle ? Hot- dipped can be shiny . If it is aluminum it's something I never heard of in 35 years of metal work .
  5. M

    Tractor rollover?

    Rolled two hay wagons on steep ground , loaded too high for conditions.
  6. M

    A genuine pandemic...

    We have 70 acres or so of woods ,50 to 60 percent ash . Don't have a lot of deadfalls yet but over the last couple years pretty much all are affected . Burned all ash in the woodstove last couple years .
  7. M

    Starting problem.

    Full tank helps
  8. M

    tree stand

    Last vehicle I found on us I took his plates off and threw em in the river . I also caught a jeep with spike strips once , kinda funny . They tore up a new seeding the day before , decided to come back the second night . 4 flats and the cops got em.
  9. M

    OT... firewood

    Pertaining to the ash borer , all my ash are dead or dying . Central NY right on PA border. Hemlocks are following suit . Ash is excellent firewood . Poplar is ok for campwood .
  10. M

    OT - Maple Syrup Advice - Adirondack Case Guy?

    There are some sugaring groups similar to this site , Google for suggestions . If you have a Facebook page there is also some groups there . Both are a great source of info . I'm a dabbler, make a few gallons for fun .
  11. M

    I've been looking welders

    I own a sheet metal and steel fab shop . We work from 24 gauge to 1/2" plate. Have 3 110 volt Miller's for all our light work . Been excellent machines.
  12. M

    Welding

    I was shocked once or twice due to water , seemed mild . Last night 6 of us were rebuilding a high pressure oven plenum while welding and crawling all over it . Not saying it can't happen but in 30 years I've only got it from moisture .
  13. M

    Ford 4000 skip

    Fuel system was my suspicion . I had replaced filter fairy recently but she has been sitting for sometime . Thanks for the help . I don't post often on here but have gotten a wealth of knowledge from everyone .
  14. M

    Ford 4000 skip

    No white smoke but definitely at higher rpm . Is that a pump rebuild then ?
  15. M

    Ford 4000 skip

    Good day all ,seeking help . Have a 74 4000 diesel . After warming up runs rough , skips etc. Have owned 5 years or so . Normal maintainence , fluids ok blah , blah. Radiator clear . Only did this last 2 times I've run it . Thanks.
    • mtny
    • Thread
    • Replies: 15
    • Forum: Ford
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top