Recent content by MZ Ranch

  1. M

    Flywheel Timing Marks JD 40 U

    I reset the points because they were only at about .014 I set them at .020 and that seemed to give the tractor more power at low end.
  2. M

    Flywheel Timing Marks JD 40 U

    I have SPARK close to center in the timing hole at full throttle going to try to get it centered better then maybe advance the distributor to get a tiny bit more power under load. Any thoughts on if might work.
  3. M

    Flywheel Timing Marks JD 40 U

    Hey guys been a while since I posted on the forum. I have a 1953 JD40 U and I am trying to time it with my timing light. There are two TIMING indication lines on the flywheel, one says SPARK and has been painted faintly with a yellow paint, the other says DC. The letters D and C, D is above the...
  4. M

    JD 40 U Starting Issue

    Hey, thank you for all of your help. All of your suggestions lead me to the problem. I wasnt going to change it over to a 12 V system, as I kind a like it as a 6 V positive ground electrical system. I tested the coil ohms and they were exactly the 1.5 for the 6 V coil. Then I tested continuity...
  5. M

    JD 40 U Starting Issue

    Hey 6cyl, thank you for all of your help. All of your suggestions lead me to the problem. I tested the coil ohms and they were exactly the 1.5 for the 6 V coil. Then I tested continuity through the coil wire to the distributor and it was good. I replaced the spark plugs and tested the spark...
  6. M

    JD 40 U Starting Issue

    Hey James thank you for all of your help. All of your suggestions lead me to the problem. I tested the coil ohms and they were exactly the 1.5 for the 6 V coil. Then I tested continuity through the coil wire to the distributor and it was good. I replaced the spark plugs and tested the spark plug...
  7. M

    JD 40 U Starting Issue

    Hey guys, thank you all of your help. All of your suggestions lead me to the problem. I tested the coil ohms and they were exactly the 1.5 for the 6 V coil. Then I tested continuity through the coil wire to the distributor and it was good. I replaced the spark plugs and tested the spark plug...
  8. M

    JD 40 U Starting Issue

    Hey guys, appreciate all of your help. All of your suggestions lead me to the problem. I tested the coil ohms and they were exactly the 1.5 for the 6 V coil. Then I tested continuity through the coil wire to the distributor and it was good. I replaced the spark plugs and tested the spark plug...
  9. M

    JD 40 U Starting Issue

    Hey guys, thank you for all of your help. All of your suggestions lead me to the problem. I tested the coil ohms and they were exactly the 1.5 for the 6 V coil. Then I tested continuity through the coil wire to the distributor and it was good. I replaced the spark plugs and tested the spark plug...
  10. M

    JD 40 U Starting Issue

    Absolutely correct this is the original 6 V positive ground system. Only one battery and its a 6 V. Thanks
  11. M

    JD 40 U Starting Issue

    Dont know Im going to presume its a 6 V coil how will I tell the difference?
  12. M

    JD 40 U Starting Issue

    I have another coil and I may put it on its the original that I took off last summer. Also as far as the condenser goes last summer I had to ask Napa for a condenser for a 1951 Chevy Engine 6V 235 because it was the same condenser. You guys are great I really appreciate all of your input and...
  13. M

    JD 40 U Starting Issue

    I totally agree the oil should have flowed through the filter and down into the pan. I am going to make sure all the ports are clear and I will put a new filter in it. I may try a thinner grade of oil just for getting it back up and running. You guys are great I really appreciate all of your...
  14. M

    JD 40 U Starting Issue

    This looks like an awesome idea. Thank you for the great detail. I will definitely try this when I get back to the ranch. Thanks for the help.
  15. M

    JD 40 U Starting Issue

    Replaced cables with 00 cables and yes I was planning on checking the oil level and making sure the seal between the hydraulics and the oil isnt leaking through. I dont think it is but with the cold weather in Idaho as we were trying to push start the tractor there is a possibility of a seal...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top