(800) 853-2651
SHOP NOW

NatWester's latest activity

Yesterday's Tractor Forums
  • N
    NatWester reacted to Dieseltech's post in the thread Injection pump timing with Thank You Thank You.
    Pump turns counter clockwise, so pull the top AWAY from the engine to retard the timing.
  • N
    NatWester posted the thread Injection pump timing in Tractor & Farm Talk.
    Long 610 4 cylinder 102mm D-121.050 injection pump: which way to twist it to advance the timing? top towards the engine? Because I think...
    • received_1323181199304346.jpeg
    • received_1031497599474880.jpeg
    • received_2411850195949358.jpeg
  • N
    NatWester replied to the thread Long 610.
    Valve clearance - is .010 too tight?
  • N
    NatWester posted the thread Long 610 in Tractor & Farm Talk.
    Long 610 -fresh rebuild: pistons, rings, honed, rod bearings, gasket kit Good oil pressure 50psi, but.... It has a rattle, gets worse...
    • Messenger_creation_1320173462825815.jpeg
  • N
    NatWester posted the thread Long 610 in Tool Talk.
    Long 610 -fresh rebuild: pistons, rings, honed, rod bearings, gasket kit Good oil pressure 50psi, but.... It has a rattle, gets worse...
    • Messenger_creation_1320173462825815.jpeg
  • N
    NatWester posted the thread Long 610 - 1st oil change? in Tool Talk.
    Long 610 4 cylinder 102mm - fresh rebuild: pistons, rings, honed, rod bearings, gasket kit. Break-in: how soon should i change the oil?
    • oil.jpg
  • N
    NatWester posted the thread Long 610 - Air Filter in Tool Talk.
    Air filter assembly, removed, bottom view. I've got the cup and the lower filter element removed. I'd like to take it apart and pressure...
    • filter.jpg
    • filter1.jpg
  • N
    NatWester posted the thread Long 610 in Tool Talk.
    Long 610 connecting rod bearing - URB 11503177 R0 - are these std? The rod journal is 2.313''
    • received_3218145045039311.jpeg
    • 20260430_144421.jpg
    • 20260430_144014.jpg
  • N
    NatWester posted the thread Long 610 in Tool Talk.
    Long 610 update: It was hard to start, had LOTS of blow-by. I got it apart.... busted ring lands on the pistons, cylinders were.... ok...
    • 1.jpg
    • 7.jpg
    • 6.jpg
    • 5.jpg
    • 4.jpg
    • 3.jpg
    • 2.jpg
Show older items
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top