(800) 853-2651
SHOP NOW

Recent content by navyreteoc

Yesterday's Tractor Forums
  1. N

    4010 pto repair for tim s or tx jim

    TAKE IT TO A SHOP. 1. Bushogs and 4010 pto,s not good. 2. There are a lot of part after you split it. 3. It's hard and cost a lot to get the MEC. to put it back together at your TREE.
  2. N

    2 star crawler on ebay

    Yell u want it back LOL
  3. N

    Swapping out JD-3020 Starter for Gear Reduction

    aluminum is a better conducter than steel
  4. N

    tx jim

    YES u r correct i will get in contact with him .. Thank you so much
  5. N

    tx jim

    220533516718 TY Jim
  6. N

    tx jim

    i hate to bother you but i need a little info. i have a 4010 and i think the pto shaft is bent and the seal wont hold it pours oil out when the pto is 1 way you can turn it and it stops leaking. there is a shaft for sale on e bay however i dont know if its right it has a gear on 1 end and is...
  7. N

    Pto shaft

    I was wondering about the internal pto shaft . is there a bearing just in from the rear seal ?
  8. N

    Splitting a 4010 LP

    TY Much TX jim
  9. N

    Splitting a 4010 LP

    I have a bent pto shaft Its the one that fits in the seal . as i understand the tractor must be split to replace this shaft . any and all help is great . where is the best or only place to attach the spliting wheels thank you for your help.
  10. N

    4010 LP

    Help My tractor is leaking oil between the gov, and the block (left hand side in front) there our 3 bolt i was wondering whats there O ring o gasket and is there some type of timing gear i dont want to take it of and get it out of time . thank you all for your time .
  11. N

    Another whats it worth question 630 NF w/pics

    Damn boys i have a 4010 LP that runs with a add on 3 pt whats it worth??????
  12. N

    4010 LP

    I put a loader on my tractor yesterday. while i was pulling into the arms i hit a hex head,or bolt on the right side right below the tack cable . it is bent now and dont want to come out real easy i was wondering what it s job is do i need to replace it or ? have good day all may god bless you.
  13. N

    4010 LP

    Yes i know about the rocks (hitting) i was not saying the tractor was weak its me thats weak. Maybe its not as bad as i think . i ran it a lot yesterday with no load and the seal never leaked . Thanks again .
  14. N

    4010 LP

    2 mo ago i was brushing hogging and i hit a rock. this caused the pto shaft to break and the pto end caught the draw bar and twisted off the pto shaft . yesterday i replaced the pto shaft (4 BOLTS) i also installed a new seal . Now my problem it looks like the inter shaft is bent. when the pto...
  15. N

    JD A two Point hitch,

    As i said i have just what u need lol
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top