(800) 853-2651
SHOP NOW

Recent content by Nebraska_Cowboy

Yesterday's Tractor Forums
  1. N

    MH 20/22/81/82 rear cover plate

    Place to check the fill level
  2. N

    101 Jr Twin Power throttle adjust??

    Did you try to losen the throttle quadrant and rotate it? I have and 81, 22, and 20 and that is the only way I was able to get the notches to line up and work.
  3. N

    Ultradog & KurtNEPA-Bumper Brackets

    Yes, we sure did.
  4. N

    Ultradog & KurtNEPA-Bumper Brackets

    I live in Columbus
  5. N

    Ultradog & KurtNEPA-Bumper Brackets

    Ultradog and Kurt NEPA, Thought I'd share the bumper brackets I was able to make as a result of your help and pictures. I think they make the 860 bumoer with the weights on it look nice. THANKS again for the help.
  6. N

    frony end loader hyds

    Where does your manual say the filter is then?
  7. N

    28 inch industrial or military style rear tractor tire

    Got a set of 28 industrials on an 8N I use for mowing. Firestone brand and the gentlemen I bought it from used it to load gravel trucks. Watch out they are expensive to buy! Worse that turf tires!
  8. N

    F 124 distrubutor

    Owners manual describes how to do this. If you don't have one, let me know by replying to this with your e-mail address and I'll scan the procedure for setting the timing & send to you.
  9. N

    2 massey harris pacer tractors

    Where are you located
  10. N

    Massey Harris 20 or 22

    What do you plan to do with one of them? the 22 has the ablilty to have a 3 pt hitch. Basically the same tractor, one will have a 124 cu inch engine (20) and the 22 will have a 140cu inch engine.
  11. N

    4000 fuel sysrtem 4-cyl

    Don't care if you can spell or not. I read your posts for the value & content. Heck I fat finger most all everyting I type. THANK YOU for sharing your knowledge
  12. N

    Massey harris 23 mustang

    Does it have a 3 point hitch, if so, probably 1500-2000
  13. N

    Paint info by Gaspump?

    Looking for a post from several years back by Gaspump. Had a real good list of colors and how parts on a 8N were painted. Searched the archives and can't seem to come up with it. Any one got a copy they'd post? Thanks in advance for your help.
  14. N

    old massy

    Look on the dash for a serial number or data plate. And no, your wiring harness for an 8N Ford will not work without a bunch of modification
  15. N

    Help needed on model number for sickle bar mower

    Belt driven
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top