(800) 853-2651
SHOP NOW

Recent content by Nimrod77

Yesterday's Tractor Forums
  1. N

    clutch for Oliver 88

    I hope it don’t jink me then. I have gone up to 5500 6mph 5th gear and hasn’t slipped yet
  2. N

    clutch for Oliver 88

    Not joking it’s all brand new stock components. I used what I had before upgrading to try it. And it’s working so far. Unless it’s something I’m not familiar with I’m no clutch expert.
  3. N

    clutch for Oliver 88

    I just use the stock 88 clutch. 500 ci holds it fine no issues
  4. N

    Clutch adjustments

    Yes yoke was removed. There’s an idea Any pics of front vs back?
  5. N

    Clutch adjustments

    I’ll double check disk. Thought single it did t matter. And clean splines up so it travels smoothly. Then put engine back In and see if anything changed. Anyone adjust the. Fingers? If so. 9/32 like manual says?
  6. N

    Clutch adjustments

    It does not have a serial number plate over the years it got ripped off I guess it’s just a regular 88 row crop. 1954. So I got new clutch discs new pressure plate. The shaft is tight going into the splines. I adjusted pedal play as manual says. 1”. And 3/4 free travel before touching...
  7. N

    Clutch adjustments

    Sorry folks. It’s a 88 tractor
  8. N

    Clutch adjustments

    so I’ve adjust clutch all over the place. It’s all new components. Still grinding into gear. No matter how close I have it to what my manual says has anyone had this issue? I adjusted the fingers even 9/32 too tight and it still does the same thing what am I missing? Any other thoughts? Would...
  9. N

    Crack in cylinder head

    Thank you all I’m going to look into all this and track somebody down appreciate the input
  10. N

    Crack in cylinder head

    It’s a 195 hard time to find this head I found.
  11. N

    Crack in cylinder head

    Anyone know a good shop that can stitch weld a crack in cylinder head. I have my engine overheating and getting air in system. Found a crack. Thanks
  12. N

    Starter

    Little help on wiring up. I got one from RE. No instructions to wire it. I do t want to hurt it before I know what to hook up. Any help would be grateful.
  13. N

    Starter

    Like a reputable place and for Oliver 88 bell housing. And a true high torque starter. Any information would be appreciated thanks
  14. N

    Starter

    I think my old starter is going. Plus it’s not used to turning higher cubic inch’s. What is a good high torque starter. I’ve searched and can’t find anything that I trust. Thanks
  15. N

    Hinton engines

    Thank you
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top