(800) 853-2651
SHOP NOW

Recent content by Ntockey

Yesterday's Tractor Forums
  1. N

    '78 2040 popping rear end

    It does have a diff lock which seems to work well. I use it often without issue. I don't think that's what I'm hearing
  2. N

    '78 2040 popping rear end

    Steel rear centers. I'll double check all the fasteners then likely look up inspection procedure.
  3. N

    '78 2040 popping rear end

    I have a '78 2040 with 145 loader, 950hrs that more and more lately is making a noise in the rear end that sounds like a combination of a pop and clunk which seems to me to be coming from inside the rear end. I can't be sure of location my left ear is deaf so locating sounds is unreliable...
  4. N

    Barring and timing tools for 2040

    I have the turning tool JDE83 and timing pin JDE81-4 which my local JD dealer said is correct and ordered for me. I also have TM4300 which vaguely states "Timing pin will enter its hole in flywheel." By my understanding, the bolt hole just below the bore where the turning tool is inserted...
  5. N

    Couple questions 2040 w/ 145 loader

    #11 in that pic is correct. Not sure why my pic didn't work. Thanks for your answer!
  6. N

    Couple questions 2040 w/ 145 loader

    <img src=https://www.yesterdaystractors.com/cvphotos/cvphoto84527. jpg>
  7. N

    Couple questions 2040 w/ 145 loader

    '78 2040 with 145 loader I used the ports where the coolant heater is plumbed into the block to drain and flush but noticed a threaded plug in the lower front right of the block. Can anyone tell me what that's for? Also, is there a kit available to service the control valve of the loader or...
  8. N

    Barring and timing tools for 2040

    Thank you Tx Jim, thats what I needed to know.
  9. N

    Barring and timing tools for 2040

    I have a '78 2040 serial number 291986 that I've been working on. I'd like to get a barring tool and timing pin. Engine tag says type 3164DL-04 Is JDE83 the correct barring tool for this engine? What timing pin is correct (JDE81-4 has been suggested to me) and where does it go? Are...
  10. N

    2040 oil in exhaust and clunk in final drive

    It has serial number 291986 and I believe it is a '78 Thank you
  11. N

    2040 oil in exhaust and clunk in final drive

    buickanddeere, can you elaborate on greasing the clutch fitting? I didn't see that in the manual.
  12. N

    2040 oil in exhaust and clunk in final drive

    Thank you both for the info. I read up on wet stacking and I agree that's likely it. Worried about working it hard because of the clunking noise though, hardest I've worked it was bush hogging 6 acres.
  13. N

    2040 oil in exhaust and clunk in final drive

    Hello all, been reading a while, first post... I have a '78 2040 with a 145 loader that sat for a decade plus and now I use it often for a range of chores. I did fluids, filters, new rear outer spin out rims, all new tires, some electrical repairs. Yet to do hoses and needs rust...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top