(800) 853-2651
SHOP NOW

Recent content by OC4-3D

Yesterday's Tractor Forums
  1. O

    1550 RC with double bevel rims

    Any words of wisdom that might help me get my wheels to run true? I have a 1550 row crop with the double bevel rims and clamps.
  2. O

    1550 power steering center cap

    Hi guys. My 1550 has power steering with the telescoping wheel. The chrome knob for locking the telescope in place has about a 2-3/4 opening. All of the emblems I can find online say for 2-11/16 opening. I bought the o-ring that the parts book references, it's way too small. The parts book...
  3. O

    PTO / Hyd Pump Shaft Splines

    Hi guys. Pretty close to driving the 1550 out of the garage, for the first time since I pushed it in here in the fall of 2014. Just need the PTO / hydraulic pump shaft installed, so I have power steering. What's the wisdom on putting any kind of grease on the splines on the flywheel end of...
  4. O

    1550 Diesel - muffler or straight pipe?

    Sure thing, go on youtube and search up Oliver66FarmBoy.
  5. O

    1550 Diesel - muffler or straight pipe?

    Thanks guys, really appreciate the feedback. I just ordered the Nelson, or at least it looks like the genuine Nelson, part number 14245T.
  6. O

    1550 Diesel - muffler or straight pipe?

    I'm getting down to the last of the 1550 restoration, it's time to order either a muffler or a straight pipe. From watching all the O66FB videos, I'm leaning toward straight pipe. Wondering what you guys think?
  7. O

    Ford 2310 valve adjustment

    Does anybody know how to adjust the valve clearance on a Ford 2310? The adjustment screw on the rocker has no jam nut like my Olivers do... is it just an interference thread that needs more torque than I can give it with a box wrench?
    • OC4-3D
    • Thread
    • Replies: 3
    • Forum: Ford
  8. O

    1550 RC short wheelbase tie rods

    Question on tie rod arrangement. Lower rod to the left and upper rod to the right?
  9. O

    Got my 88 done

    Awesome job! Love seeing’em out working. That red strip down the grill really makes it sharp looking.
  10. O

    Hyd line clamps

    Have you guys ever run across somebody who can re-furb these cast iron hyd line clamps?
  11. O

    770 diesel in a 1550

    So it turns out my 1550 was born with a gas engine, and one of the previous owners swapped in a 770 diesel. “Pretty close to the same” but it looks like it was done in a hurry. Hoping you guys will give me some advice regarding the radiator. It looks like it will be easier to fabri-cobble the...
  12. O

    Oliver 1850 steering gear removal

    The quad ring (item 12 in the pic) is Agco P/N 155788A, supersedes to 72160219. About $5.
  13. O

    1550 brake pedal shaft bushings

    So I spent quite a bit of time pressing the bushings out of the brake and clutch pedals, thinking I could find new ones. Not so much. You guys are my last hope - before I try pressing them back in. Anybody know if/where I can find these? Chuck
  14. O

    1550 axle question

    My 1550 RC has identical axle shafts L and R, both with 1 keyway. Not sure if wide tread or industrial would have 2 keyways, but I’d say it’s likely one has been changed out on yours.
  15. O

    Hydramotor checks

    Hi guys. Learning many lessons here, like don’t disassemble things, wait 4 years, and expect to remember how it all went. Anyone know how the check balls are supposed to go in? Ball first or spring first? Parts book shows ball first but I’m just not sure.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top