Recent content by OK_BobL

  1. O

    So Long

    I am going into Hospice this week, with fast moving Leukemia, moving to an assisted living facility, and just want to say goodbye to the finest bunch of guys I have ever known. My 660 , 2N and 8n, along with the f150's and f600 are sad I'm sure, but they will be fine. I just wanted to say that...
  2. O

    3-Point and a Dirt scoop

    Thanx for the replies guys. When the temp gets back above 10 or 15 degrees, I'll try what Terry says. The only problem I'll probably have is getting the sway bars over far enough on both sides to fit over the pins. They are so tight I have problems fitting them onto most of the equipments...
  3. O

    3-Point and a Dirt scoop

    I use a KK scoop to move dirt and gravel. I have trouble with the scoop getting into the ag back tires. I don"t use the stabilizer bars because of the 3-point pins on the scoop being pointed inwards. The way they were installed at the dealer and the way they are shown on KK net site picture...
  4. O

    F 600 Dump Bed

    Just bought a 1961 F600, with dump bed. The label on the dump cylinder says TRO JAN Truck Lifts, Wichita, KS. Does anyone know of info/manuals/etc for this lift and bed? I think 13 foot bed. Working fine right now. Found the F600 1961-2-3 shop manuals on cd-rom and have ordered a ford owners...
  5. O

    Shortening a PTO shaft

    You might look at this link. There are good instructions on how to shorten the shaft if needed. Bob Untitled URL Link
  6. O

    Thanks To Everyone For Your Knowledge

    I"ve had a 660 for about 1 1/2 years now. Used for several little things around the place. It had a 1 year old complete engine overhaul on it when I bought it. I have never been satisfied with the starting, running, power, sound of engine. Using choke some all of the time. Backfires. Hard...
  7. O

    600 Hydraulic Pump

    Thanks, Wayne. I didn't know how it was plumbed into the sump. At least now I can plan an approach and not be too surprised. Bob
  8. O

    600 Hydraulic Pump

    Have a 1955 660 with piston type hydraulic pump. I need to replace the orings in the manifold to stop leak on rear where it ties into the intake line. When I take the manifold off, will the hydraulic sump try to drain from the low pressure line from the sump? I"m sure I"ll get some draining...
  9. O

    O T Who?

    Does anyone know who gets the first $1,000,000,000.00 in cash from the bail out? Just thought it might be someone I know! Bob
  10. O

    660 Gas Shut-off Valve

    Glen, thanks for the idea. There's a small drilled hole in the side of the hood, in line with the screw with a sort of small worn/rusty spot around the hole that looks like someone over the years has had some kind of extension from the valve thru the hood to the right side of the hood. I should...
  11. O

    660 Gas Shut-off Valve

    I don"t want to be a complainer, but I have a lot of trouble turning the fuel off and on using the screw under the fuel tank. At my age and with a old Ford FEL on the tractor, twisting my arms around on my knee and trying to reach the screw with a screwdriver over the FEL frame, under the hood...
  12. O

    Modern or Classic view

    Cancel my non-vote. I just remembered, I quit voting for anything after I passed 75. Bob
  13. O

    OT... For the herbalists...

    Looks like 'Poke', maybe. Bob
  14. O

    Modern or Classic view

    Classic Bob
  15. O

    OT - Safety

    Probably a seat switch like the lawn tractors have would be better than nothing. At least it would make it difficult to run the engine when off the tractor. Bob
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top