(800) 853-2651
SHOP NOW

Recent content by Old case Mike

Yesterday's Tractor Forums
  1. O

    MW piston

    Is there enough room using a MW piston sp46 with a WD45 crank in a WD block I know it will be high compression motor ,it will only be a pulling tractor for dead weight
  2. O

    Bull gears

    Yes I have a manual there not to tight glad they are back in
  3. O

    Bull gears

    That was a learning experience swapping those out bull gears chains are tight. Now to put it back together hood looks good too
  4. O

    Fordson F Carburetor Conversion

    I took a vaporizer manifold flipped it upside down made a plate to bolt a updraft carburetor on it worked well
  5. O

    Bull gears

    What is the trick to removing axle shafts on a case DO Looking to change bull gears
  6. O

    Fordson F

    I have a 1936 English fordson I will take it out to plow day for a work out once a year its on steel now but I have cut off rubber for it .they was featured at Oakley mi few years back probably only a handful there. Its a good old work horse for what they are
  7. O

    D Bull gears

    Hey mEL I’m going to be running a DO for pulling I have 4 inch pistons at the top of the sleeves. 5505 head will be used I’m wondering what would be the better bull gears 38 or 31? I believe it has 31 in it. I will be using 16.9 or 18.4 26 inch tires this tractor is just getting started for...
  8. O

    D Bull gears

    Hey mEL I’m going to be running a DO for pulling I have 4 inch pistons at the top of the sleeves. 5505 head will be used I’m wondering what would be the better bull gears 38 or 31? I believe it has 31 in it. I will be using 16.9 or 18.4 26 inch tires this tractor is just getting started for...
  9. O

    Case Do

    I ratchet strapped a wc gas tank to rear wheel of case cc put it on a jack stands fired it up put it in gear.i filled the gas tank with nuts bolts an washers
  10. O

    case cc high compression pistons sleeves

    Piston is 100 thousands up out of sleeve
  11. O

    case cc high compression pistons sleeves

    Yes 3-7/8 pistons already installed in block my 5505 head has new guides seats 30 off deck. 5576 head I have has to go to shop if I use that one gonna stone boat it for just fun nothing serious.
  12. O

    case cc high compression pistons sleeves

    I put nos high compression pistons for C-D series tractor in a cc case I'm using a 5505 head not nuff room pistons hit the head is this set only for 5576 head 250 cc I'm using 5505 head 200 cc. From top of old piston to top of ring is 3/16 inch new piston from top to first ring is 5/8 can anyone...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top