(800) 853-2651
SHOP NOW

Recent content by oliver2-44

Yesterday's Tractor Forums
  1. O

    White/Oliver 2-44 Injector Pump Removal and Turning Engine for Timing

    I got to spend some time working on the tractor Saturday. I searched and searched for that timing hole, I was about ready to give up when there it was right in front of me. the loader frame and hoses certainly made it less obvious. I bumped it around with the starter a few times, trying to...
  2. O

    White/Oliver 2-44 Injector Pump Removal and Turning Engine for Timing

    Thanks, I'll be at farm briefly today with the holiday and family things. I will at least have time to find the hole and get an idea how to proceed. I'm suprized there is no mention of this in the manual I have.
  3. O

    White/Oliver 2-44 Injector Pump Removal and Turning Engine for Timing

    Well it's been awhile, with the holidays it was Jan 2nd when I finally pulled pump. took me 2 trips down to the farm, because I had to bend a box end wench flat to get the one bolt on the back side of the pump out. The shop (Premco, Lampasas , Tx) had a few internal items on backorder for a...
  4. O

    Identifying White Oliver 2-44 TLB Year and Power Steering Cylinder

    Thank you for the video, 63 to 82 Corvette is what i needed to know. Unfornatualy there is no nameplate, is the serial number just stamped into the casting? Possible filled with paint ?
  5. O

    Identifying White Oliver 2-44 TLB Year and Power Steering Cylinder

    I have a white Oliver 2-44 TLB, with the 588 Loader and 613 Backhoe (per the decals) I bought it salvage in 1994 with a broken top shaft bearing holder in the shuttle transmission. I bought a transmission and rear end off a 550 or Supper 550 that had been in a fire. So I lost the nameplate...
  6. O

    White/Oliver 2-44 Injector Pump Removal and Turning Engine for Timing

    @tom upton Thanks for the reply. I appreciate the info on the energy cells as I've never worked with the. A few questions. I'm going to double check, put yes I think pump is not turning when cranking engine. Tractor is at family farm 2 hours away and I usually am there by myself. I can jump...
  7. O

    White/Oliver 2-44 Injector Pump Removal and Turning Engine for Timing

    I have a White/Oliver 2-44 that must have gotten some water in the injector pump and rust/froze it up. it had a new filter on it, then I loaded it to someone where it sat outside for a year+ I have the Oliver 550 IT Manual with instructions on how to pull the injector pump and how to time it...
  8. O

    White/Oliver 2-44 Injector Pump Removal, How to Turn Engine For Timing.

    Thanks, @m16ty Unfornatualy a mobile heavy equipment mechanic I talked to in the area said water probable got in the pump rusting it and then the pump shaft probable broke when I tried to crank it after it sitting for a year. So nothing rolls to see it in the little injector pump window. The...
  9. O

    White/Oliver 2-44 Injector Pump Removal, How to Turn Engine For Timing.

    I have a White/Oliver 2-44 that must have gotten some water in the injector pump and rust/froze it up. it had a new filter on it, then I loaded it to someone where it sat outside for a year+ I have the Oliver 550 IT Manual with instructions on how to pull the injector pump and how to time it...
  10. O

    Oliver 2-44 (550) Power Steering Cylinders Needed

    This message is a reply to an archived post by wisconsin cowman on March 01, 2018 at 11:47:36. The original subject was "Re: Oliver 550 power steering cylinder". In the above archived post its mentioned that the ford 4000 power Steering cylinders will fit on an Oliver 550. Is it the early...
  11. O

    1982 John Deere 108 transaxle problem

    I had a 1984 JD 116 with peerless transaxle that did the same thing. As someone else mentioned it sounds like the shift keys need replacing. It not a hard job. PS After you drop the transaxle there is a recessed area in the center of the housing that has a bolt in it. This can easily be...
  12. O

    white 2-44

    I have a 2-44 with loader & backhoe that had been heavily used. I bought it 20 years ago for salvage as the transmission would not stay in gear. When I opened it up the upper shaft front bearing cap had broken and the lower part of that front bearing mount was damaged from it being used that...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top