(800) 853-2651
SHOP NOW

Recent content by OliverMan1855

Yesterday's Tractor Forums
  1. H

    A whole lot of hours

    Hello all. I finally got down to business on replacing the tach on my 70 lp. The tach hasn't worked since my Dad last used it to plant cotton in 1989. Anyway, I inspected it closely and found that I could still read the total number of hours. I couldn't see how many tenths, but the whole number...
  2. O

    Looking for a junk schwitzer 3lm or exhaust housing

    Looking for a junk schwitzer 3lm or exhaust housing
  3. O

    Looking for a junk 3LM turbo or a exhaust housing

    ya
  4. O

    Looking for a junk 3LM turbo or a exhaust housing

    Looking for a junk 3LM turbo or a exhaust housing.
  5. O

    3LM exhaust housing size?

    Does anyone know the exhaust housing size in CM"s on a 3LM turbo?
  6. O

    Farmall M more power

    can you build the m carb to be the same as a 450?
  7. O

    M is getting coolant in oil.

    We had a couple m's in tech that had that problem. All were cracked heads. I would pull the head and have it pressure checked, sometimes if the head studs are not sealed right they will leak also.
  8. O

    What to do! Anti-freze in oil on 400

    probably a cracked head
  9. O

    Notch in 706 cylinder wall

    Looks like erosion, cavitation. And there is minerals in the block "the brown crap". there are 2 282's at school new blocks that did not have any notches i recall. Make sure when you build it you use distilled water with he coolant if its a concentrate other wise tap water will cause all the...
  10. O

    Farmall M more power

    completely rebuilding my 1941 M, got a ground crank "the late crank" rods all in spec and sized with the pins. Have the Red Power 4inch overbore kit with step head pistons ready to be put together. Wondering what else i can do to get more hp, looking to try to get 60+ hp.
  11. O

    Ford 401 puller valve springs

    i wish i could get my tractor that light. I would like to get some head studs for next year. I had to do quit a bit to get the power out of the 8000 engine though.
  12. O

    Ford 401 puller valve springs

    https://www.youtube.com/watch?v=48a94n20fiE
  13. O

    Ford 401 puller valve springs

    Had a lot of help off of year, this year was my best year took home a trophie from every pull i went to. Dynoed 230hp at school, ended up swapping motors and blew my head gasket towards the end of the season but was running strong
  14. O

    Ford 401 puller valve springs

    Does anyone know a good heavy valve spring i can run in my Ford 8000 puller? Running 3200rpm, doing a valve job after i blew my head gasket.
  15. O

    9600 ford disappears water

    I think I am having this happen to my ford 8000. My coolant is very nasty looking, looses half a gallon in short while. I also have coolant drips out of the vent tube on the valve cover but no milky oil, I did have this grayish white crap in my vent tube and oil fill neck. But the oil is black...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top