(800) 853-2651
SHOP NOW

Recent content by only know deere

Yesterday's Tractor Forums
  1. O

    Kub cutter

    I have recently purchased a restored cub farmall and have acquired a Kub cutter brush mower that's is in good condition,itfits on the rear of the tractor with one for lack of a better term fast hitch looks like to me a factory hitch on the cub. I am missing the pto shaft on the brush mower, any...
  2. O

    Kup Klipper

    I have a Kub Klipper 46in mower made by Sunflower Manufacturing it is in very good shape its been in a shed for years It was made to fit on a farmall cub but I have no arms to attach the mower to the tractor. It looks like some kind of single fast hitch any info would be a great help also is...
  3. O

    First reduction gear change

    Hi Mark I while ago you had information on first reduction gears on a unstyled A jd. I has some 620 gears pressed on my 1936 A to slow it down a bit, Now I found out the first reduction gear cover is to small because the gear on the transmission is bigger. My question is do know if a styled A...
  4. O

    First reduction gear change

    Thanks Mark I located some 620 gears and will try to press the ring gears on my existing ones. Any other tips you have would be greatly appreciated as I have not tried this before.
  5. O

    First reduction gear change

    Thanks Mark that's what I was looking for.
  6. O

    First reduction gear change

    Thanks for the information I am running a unstyled A JD it turns about 75hp on a dyno. I run out of power in third gear other A JD that I pull against seem to pull third gear fine and I don't think they have more power than I have. I think I am just in between second gear not lugging the motor...
  7. O

    First reduction gear change

    I have a unstyled A JD I have been pulling for some years it pulls ok with some trophies. My question is does anyone have information on changing the first gear reduction to a styled A to give me a slower ground speed? I was told it makes a difference.
  8. O

    cut off relay problems

    Thanks I will try it.
  9. O

    cut off relay problems

    I tried repolarizing my cut out switch, ordered a new cut out switch and like some one said that one is no good either. My question is instead of adding another switch to shut the current off when the tractor is stopped couldn't I just wire the ignition switch in line of the cut off switch and...
  10. O

    cut off relay problems

    I am not familiar with a bridge rectifier where can I get one and do I use in place of the cut off relay or wire it in line before the relay? Thanks.
  11. O

    cut off relay problems

    Thanks for the advice I will try it.
  12. O

    cut off relay problems

    I have a 1941 9n with a single pole generator front mount distributer six volt battery. I wired it like the diagram I got off yesterdays tractor I assume it is stock like it was in 1941. The trouble I have the tractor runs fine starts good but when I shut the key off the amp gauge discharges and...
  13. O

    ford 8n starter switch

    Alternator, aftermarket three position switch
  14. O

    ford 8n starter switch

    I have been working on a ford 8n sometimes when I turn the switch off and the tractor stops running the amp meter will stay discharges 20 amps. It will stay that way and then the starter switch will not engage the starter. Until I either move the shifter or press on the switch or a combination...
  15. O

    Rust on the innertube

    Is there a good way of getting the rust pieces off of an old inertube? Othet than scraping them off. Will soaking them in any solution help?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top