(800) 853-2651
SHOP NOW

Recent content by Paul1916

Yesterday's Tractor Forums
  1. P

    2096 3pt internal rod broken again

    Thanks for the tips. We are still looking at all of the adjustments the service manual mentions and that every thing is timed also. One thing I noticed is that the draft cable end is bent right where it attaches to the arm on the bottom of the case. I am not sure what happened first - some other...
  2. P

    2096 3pt internal rod broken again

    We have had the internal rod that goes from the piston to the rocker arm break twice on this tractor. The last time the broken rod must have gotten wedged against the cylinder / sleeve and pushed on the side bending it and breaking a chunk out of the rear end casting. We have the parts to...
  3. P

    1850 diesel orbital power steering motor

    Just a follow up on the original problem. I took the steering motor apart and the issue was the c clip on the bottom of the motor shaft was broken. Since I could not get this part through Agco I ground off the ears of a high quality snap ring of the right size and put it all back together. I put...
  4. P

    1850 diesel orbital power steering motor

    Yes, will have to tear into once I am finished using it for the fall. I feel that the inner shaft must be what is moving back and forth in the valve body (hydra motor) because when you push down on the steering wheel is the only time you can steer it normally, if you just try to turn it normally...
  5. P

    1850 diesel orbital power steering motor

    I have had a leak up the steering shaft for a while now and the top needle bearing fell apart about a year ago- I figured as long as it steers fine just run it... Well now it does not! I can steer it if I push down on the steering wheel with about 20 or 30# of pressure but when you let go the...
  6. P

    6230 Hyd. flow/ volume to planter vac. drops

    Actually, you did help me, you mentioning the 2nd valve got me thinking about checking it one more time and it turns out we must not have tried the 2nd valve- it works as it should. When you raise the planter and continue to hold the lever it does not slow the fan down. The reason we did not use...
  7. P

    6230 Hyd. flow/ volume to planter vac. drops

    Thanks for the reply, in talking to the dealer and doing some research I can not find a priority valve on the tractor. We have also tried all the different combinations of hooking it up using all 3 sets of SVC's and it did not change any thing. I believe the load from a 4 row planter is pretty...
  8. P

    6230 Hyd. flow/ volume to planter vac. drops

    Hi, Tractor is approx. 2008 JD 6230, we are running a 4 row vacuum planter with it. Pressure checks right at 3000 psi. The issue is you set the vacuum level and it maintains it correctly until you lift up the planter. When you use the other remote the vacuum level drops to almost nothing...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top