(800) 853-2651
SHOP NOW

Recent content by PeteEllis

Yesterday's Tractor Forums
  1. P

    land plow 300U and mc 211

    Have 300 Utility and McCormack 211 two bottom plow on tow point hitch . left plow is great but right only takes half a cut. do I have to move the right wheel out or can I make some other adjustment??
  2. P

    6v gen

    thanks john I get lower output like you guys said but gets enough for now.
  3. P

    6v gen

    can I get 12 V from a 6 volt gen if I spin it faster and put 12 v regulator o n it
  4. P

    300 pto ?

    thanks guys I thought that was the system but did not know details
  5. P

    300 pto ?

    300 utility PTO engage lever up or down ?? offpsite stops it?? how to adjust the two set screws u nder little cover on rear? thanks
  6. P

    MW Dyno help

    I can e mail you some pages from my 400 book if you don't find anything better [email protected]
  7. P

    A gen belt replace

    do I need to remove the water pump to replace Gen belt on farmall A
  8. P

    oil craftsman 917 gt

    how do I check the oil in the rear of hydro craftsman 917 tractor I read that it is sealed at factory. but need to add if change filter.. what level and what oil
  9. P

    420c hood

    replacing hood on 420C. both old and new hoods contact back of exhaust pipe solidly. casting on manifold is T 10369 do I have the wrong ex manifold.??
  10. P

    h mipulse rotor

    when the impulse mag trips does the impulse mag sent spark to the rotor before the rotor moves or as the rotor is already moving. in other words do I point the rotor directly at the #1 clip on the capjust before it trips or does the rotor travel as it is sending the spark ??
  11. P

    hard start briggs twin

    hard starting briggs 16 hp twin starts and runs great when cold but hard to restart after it warms up any ideas?
  12. P

    New Here

    listen to randy at neblinc. he has posted some real helpful stuff here
  13. P

    1948 Farmall H hydraulic belly pump, advice ?????

    thanks for pics and advice on pump rem oval of H made it easy and simple appreciate your effort and pictures
  14. P

    H magneto timing

    thanks jim that was the blue ribbon item i was looking for could not remember lh rh seting
  15. P

    H magneto timing

    what is the timing of the rotor driven gear to the drive gear at the back of the H magneto
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top