-
P
select o speed questions
What did I say that would imply I didn't read every post? There is no ambiguous info in my post. -
P
select o speed questions
Changed the filter today, also checked my band adjustments. The tractor seems to run and drive great. I don't seem to have any slipping in any gears when applying the brakes. It does still move on hills in park, but I found when I place it in park, while holding the brakes, and then "bump"... -
P
select o speed questions
Had a busy weekend at work so no time to work on the tractor but than you for all of your help. My filter arrived so I will change that and re-adjust and update -
P
select o speed questions
Will go out and mess with it again this weekend probably! -
P
select o speed questions
^^^ Exactly. I'm pretty sure mine is correct, I just was curious if the procedure is much different between different ones. -
P
select o speed questions
I havent ran it enough to see if it "runs away" downhill, but I'm pretty sure it doesn't. The "procedures" i'm referring to are for the band adjustment. My ford book has a dedicated SOS section at the beginning, and another SOS section in the middle. One says that band 1 should be adjusted... -
P
select o speed questions
I did, thank you for that. I hate to buy another manual, if mine is correct. I guess my question is, does anyone know how the procedures differ between different SOS models? -
P
select o speed questions
I do have the manual, however questionable whether its the right one. I have the original FORD manual for 54-64 4 cylinders. -
P
select o speed questions
Editing is temp disabled, it WON'T hold on a hill in PARK -
P
select o speed questions
I have a 4000 4 cylinder diesel (1964) and I adjusted the bands, and changed the fluid. The tractor runs and shifts great, however after the band adjustment, it would hold on a hill in part. I have heard the procedure is different on different select o speed transmissions. I went by the manual... -
P
Ford 801/4000 diesel Cylinder head rebuild cost
Thank you but I meant the tubes that those lines connect to. (from the side of the head to the injector) I imagine I have to buy a complete injector -
P
Ford 801/4000 diesel Cylinder head rebuild cost
Where did you see the tubes? I figure I can get a rebuilt injector for around $75. -
P
Ford 801/4000 diesel Cylinder head rebuild cost
Bought a 1964 ford 4000 that was sitting over the winter and mice got into the exhaust and their "leftovers" got into the #4 cylinder and built up to half and inch. (talk about stink!) The guy went to start it and it "hydrolocked" so to speak. So I bought it as is. I took the head off, and got...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy