(800) 853-2651
SHOP NOW

Recent content by pullerboy88

Yesterday's Tractor Forums
  1. A

    grab hooks for fuel tank CHROME

    Need a few Grab hooks for my 730 and 800 s chrome strips on the fuel tanks ,, Perhaps some one has the original manufactured parts Squirrled Away ,,, But so Far it looks like I will have to make them by Hand , and I fear they will not hold as good as the originals ,,, , Sure don't want to...
  2. P

    Econo Mod V8 puller

    gfs i am looking for an oliver chasis of a Farmall chaisie i would like to know more information on the oliver.
  3. P

    Econo Mod V8 puller

    BOWTIE I am wanting to build a mod v-8 puller. They allow us up to 410 cubs for small block and 472 for big block. I was wondering what kinda tractor should i look for and what kinda block should i use. Any help would be would help me out a lot.
  4. P

    antique tractor pulling?

    Ok. I have a small block but i am out cubing all of them though. I am aloud 410 cube and 8,000 rpm
  5. P

    antique tractor pulling?

    Hey MAPTA i noticed your club had some tractors with v-8 motors in them. What is the cube limit on that class? Can you run cut tires if so how big? Do the motors have to be big block or small block? Might come down and play with you guy's
  6. P

    antique tractor pulling?

    Hey MAPTA i noticed your club had some tractors with v-8 motors in them. What is the cube limit on that class? Can you run cut tires if so how big? Do the motors have to be big block or small block? Might come down and play with you guy's
  7. P

    WC pulling engine parts

    just put the d-17 motor in your wc and be done with it. If you don't want to do that i know a guy in ky that will be abel to help you out.
  8. P

    NATPA- div. 2 split

    WTW where are you located i am needing to get a set of 15x5.38's cut but i don't know how i want them cut. I know there is not enough tread to top cut.
  9. P

    AWWWW,,,,,,

    Chads I have to back you up 100% no one is the pulling places like diffrent. So what if your H is 100hp or 50 hp it only means you put your stuff together right the first time. Let them say you don't know what your talking about or what ever eles they want to say. I say this though if i was to...
  10. P

    PTO dyno testing for rule enforcement

    The club i pull with you can beep up to the 75 foot mark after that you get DQD and that levels the playing feild with the big hp tractors at 3 mph
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top