-
J
Massey Furgeson 57 4 btm rollover plow
This message is a reply to an archived post by Suffolk1 on October 26, 2011 at 15:52:11. The original subject was "Massey Furgeson 57 3 btm rollover plow". how much does a 4 bottom 57 massey rollover plow weigh , and will a 656 IH DEISEL lift and pull it .......... thanks jeff- jeff 0
- Post #1
- Forum: Implement Alley
-
Q
2n oil pan
I need to find where an oil pan can be purchased for my 2n. Can somebody please advise me? Thanks- quiggs12
- Thread
- Replies: 4
- Forum: Ford 9N, 2N & 8N
-
Q
JD STX 38 Mower
Thanks a lot. I will give this a look and see if I can figure it out. I can't imagine it being the solenoid because it is brand new... and it does everything EXACTLY like the one I replaced with it.- quiggs12
- Post #1
- Forum: John Deere
-
Q
JD STX 38 Mower
I have a 12.5 HP Kohler engine run JD riding mower. I just bought a new starter directly from kohler and am still have issues with it. The key won"t start it/ It doesn"t even click, making me think there is maybe a safety switch somewhere that is blown preventing it from working. However, when I...- quiggs12
- Thread
- Replies: 3
- Forum: John Deere
-
Q
19-97 loader
I am looking for some help with a Ford 19-97 loader. I called the Ford dealer to ask about a replacement cylinder and they can't even find this model loader. The guy told me I was giving him the wrong numbers... I told him that this was EXACTLY what the tag said on the loader and got nothing...- quiggs12
- Thread
- Replies: 10
- Forum: Ford 9N, 2N & 8N
-
Q
2N transmission oil
Do I get just a straight SAE 90 oil or is there something else that I can use??? I live in Maine so it does get cold and I know I am suppose to use 80 if it is below freezing. Thanks- quiggs12
- Thread
- Replies: 2
- Forum: Ford 9N, 2N & 8N
-
Q
Starter problem... NEED HELP
Why is there a cotter-pin in the bottom of these??? I have one on mine and it looks to be there in your picture.- quiggs12
- Post #1
- Forum: Ford 9N, 2N & 8N
-
Q
Starter problem... NEED HELP
tried but couldn't tell if it was in there...- quiggs12
- Post #1
- Forum: Ford 9N, 2N & 8N
-
Q
Starter problem... NEED HELP
Probably should have mentioned it is a 1946 2N. Thanks- quiggs12
- Post #1
- Forum: Ford 9N, 2N & 8N
-
Q
Starter problem... NEED HELP
My starter broke so I took it off to have it rebuilt. However, the large spring and one of the washers that holds the spring on were not on the drive. I don't want to put the rebuilt starter on if those parts are in the tractor. How can I get these out without breaking apart the tractor??? Can I...- quiggs12
- Thread
- Replies: 9
- Forum: Ford 9N, 2N & 8N
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy