(800) 853-2651
SHOP NOW

Recent content by R puller

Yesterday's Tractor Forums
  1. J

    Shell Lake, WI Tractor Pull Sept 2, 2012

    SHELL LAKE TRACTOR PULL Sunday Sept. 2, 2012 10:00 weight in, 11:00 pull starts Track Patrol Eliminator There will be a pay back in all classes except farm which will be a trophy FARM ($20 per hook) 3,500 - 4,500 - 5,500 -- 4 MPH 7,000 - 9,000 - -- 6 MPH 10,500 - 12,500 - -- 8 MPH 13,500 -...
  2. A

    ta - straight shaft confusion

    What is the difference between a t/a eliminator and a straight shaft ?? Do you not need a t/a elimintor with a straight shaft ?? Or is it one in the same ??
  3. F

    Farmall 450 gas was it 6 volt or 12 volt originally

    Restoring a Farmall 450 gas and was wondering if it was 6 or 12 volt originally thanks
  4. R

    wheelhorse d 250

    I found a d 250 2wd four cylinder gas a guy has and is lookin to sell. It runs, but has had some rough use on the deck. He says to make a reasonable offer, but I don"t know what they go for. I know parts are hard to come by. Any help would be great.
  5. R

    John deere R

    I know some of you guys out west have some R"s that pull like hell. I saw one at the rough and tumble. I will only be pulling in CT and am looking for some detailed help on how to improve my tractor, especially the gasket sets after engine work is done. It will pull 8500# class on the...
  6. R

    R engine mods

    I am looking for specifics on boring an R to accept 730 pistons. Are the stock cylinders able to be bored this far? I have the 730 pistons, but would like to find out what other steps are required to complete this job before I get into it. Thanks for all the help so far
  7. R

    '50 John Deere R

    Are the cylinders thick enough for such heavy boring, or are new liners put in?
  8. R

    John Deere

    Thank you
  9. R

    '50 John Deere R

    I"m trying to get some ideas on adjustable pulling hitches and wheelie bars for the R. I realize it won"t wheelie, but the bars are required to pull in my area. Also, any info on some extra horsepower would be great.
  10. R

    John Deere

    Looking for any help on the hitch/wheelie bar setup for an R. Any pictures would be appreciated. Also, any tips on engine upgrades for pulling would be nice
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top