-
R
Ford 19-551; 755 series backhoe hydraulic tubes
I have a 1971 Ford 4500 with a 19-551; 755 series Backhoe. One of the "hidden" hydraulic tubes in the boom is leaking. The tube is for the bucket cylinder and the Ford part number is 7705249. I have called 3 dealers including Messick s and the part is no longer available. I have searched for... -
R
Ford 3cyl diesel in 4500 TLB
I forgot to mention there was no blow by or vapor coming out of valve cover area with oil filler cap removed. -
R
Ford 3cyl diesel in 4500 TLB
I followed your suggestion and loosened up each injector line 1 at a time. The middle cylinder is not firing as there was no decrease in engine speed with the line removed. There was also no decrease in smoke with any line loosened. There was an immediate decrease in engine speed when line 1... -
R
Ford 3cyl diesel in 4500 TLB
I was using my 1971 Ford 4500 with a 3 cyl 201cid diesel engine today and it suddenly started blowing blue/grey smoke. The engine was recently rebuilt and has about 50 hours on it. It had been running fine for about 45 minutes while I was using the backhoe to move some dirt. All the fluid... -
R
750 series backhoe backfill blade
I am looking for information for a Ford backhoe bucket backfill blade. The Ford part number is 19-260 and it is suppose to bolt on to an 18” or 24” backhoe bucket. A picture is shown in the 750, 753, 755 series Ford Backhoe operator’s manual and it is mentioned on the Ford parts sites, but it... -
R
Ford King Pin Set DEPN3115A vs. Moog 8459B
Hi, I need to replace the King Pins and Bushings on my 1971 Ford 4500. I saw a post on this site and I saw a note on the Amazon site about using the Moog 8459B kit as a less expensive option to the DEPN3115A kit. Has anyone else tried using the Moog 8459B kit on a Ford tractor and did it work... -
R
Ford 4500 kingpin replacement mystery shims
Thanks pomester; that clears up what the reaming is needed for and thanks for the link on the spindle rebuild on a Ford 4500. Based on the information I saw in the link it looks like this could be a challenging job. So far I haven’t even be able to remove the Spindle Lock Pins. I have tried... -
R
Ford 4500 kingpin replacement mystery shims
Hi, I need to replace the King Pins and Bushings in my 1971 Ford 4500 and I did see a note on the Amazon site about using the Moog 8459B kit as a less expensive option to the DEPN3115A kit. Has anyone tried using the Moog 8459B kit and did it work without any problems or modifications? On... -
R
Ford 201 cid 3 cyl. Diesel exhaust soot in rebuilt engine
I would like to thank everyone for your feedback. It is true; so far I have not worked the engine as I have been working on the hydraulics so I can raise and lower the buckets in order to move her around. It has only idled between 1,000 and 2,000 rpms and I have noticed it runs very cool at... -
R
Ford 201 cid 3 cyl. Diesel exhaust soot in rebuilt engine
I recently had my Ford 201 cid 3 cylinder Diesel engine from my 1971 Ford 4500 TLB completely rebuilt. I installed it and have it up and running and it currently has about 4 hours on the engine. I have been running it without a muffler and have noticed I am getting a bunch of small oily soot... -
R
Ford 4500 engine rebuild - now Clutch problems
Thanks, I think I have the problem resolved and your mentioned of pedal Freeplay pointed me in the right direction. I checked the Freeplay which was about 1”, but that led me to think about the total pedal travel especially down to disengage the clutch. I had changed out the left side running... -
R
Ford 4500 engine rebuild - now Clutch problems
I had the 3 cyl Diesel engine rebuilt on my 1971 Ford 4500 TLB and installed it last Nov. Since then and while I had it apart I have been working on the hydraulics and rebuilt a few cylinders and hyd pump. I finally got it all back together and the hydraulics appear to work fine, but I can’t... -
R
Ford 4500 Instrument Cluster
I am try to get my Instrument Cluster working again. When I apply 12 volts to the B terminal on the Voltage Stabilizer on the back of the Instrument Cluster all of the other terminals on the Instrument Cluster show they are energized with 12 volts. In fact it looks like the entire... -
R
Ford 4500 with a 19-551 Backhoe; Swing Hyd. Cyl. Rebuild??
Thanks JF, Since I'll have to remove the entire Backhoe unit to get at the Swing Hyd Cylinders I will have to wait until I get the Stabilizer Hyd Cylinders rebuilt and reinstalled. This will be more of a challenge than I thought. It looks like someone might have already tried to rebuild 1... -
R
Ford 4500 with a 19-551 Backhoe; Swing Hyd. Cyl. Rebuild??
Hi Folks, I have a 1971 Ford 4500 with a 19-551; 755 series Backhoe. I just removed the stabilizer Hydraulic Cylinders so I can rebuild them as they both leak and will not stay up or securely down for any length of time. In the process I noticed both Swing Hyd. Cylinders are also leaking...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy