(800) 853-2651
SHOP NOW

Recent content by Rays

Yesterday's Tractor Forums
  1. R

    hd6 ag

    What is the serial no. of your HD6 Is it Power shift or does it have a hand Clutch I have a lot of books for these tractor so I should be able to come up with no. or filter you need let me know you can give me a call if you like 330-223-1913 Thanks, Rays
  2. R

    IH TD6

    This is for Tim in Alaska I have a good used head for a four cylinder TD6 INT crawler tractor. Let me know what your casting no. is I will match mine to make shure they are the same. I am located in Ohio My Phone no. is 330-223-1913
  3. R

    JD4055 Parts

    Looking For a Clutch Housing Complete for a Jd 4055 Four wheel Drive power shift Casting No. is R83113.
  4. R

    td8e steering problems

    Hi, What your problem with your steering I have work on some TD8E over the years and can all so get used and new aftermarket parts for these machines. Let me know if I can help. Thanks, Rays
  5. R

    TD6-62series brakes

    Do you have two piece or three piece bands let me know I will check I might have some. Thanks, Rays
  6. R

    Case 350 Parts

    No donot have a radiator what I have is the final drives, Torq,Bottom Rollers, Rock guards Thanks, Rays
  7. R

    Case 350 Parts

    I have some parts for a 350 Case
  8. R

    4055 Parts

    Looking for Clutch Housing With gears for a JD 4055 4 wheel drive powershift anyone help call 330-223-1913 Thanks, Rays
  9. R

    MF 200 Parts Book ?

    Hi Jim, I have two relined brake bands for a 200 Massey if interested email or call 1-330-223-1913 thanks, Rays
  10. R

    TD 340 A pins

    MMi,The pins+bushing are $840.00 for a set, Thats both tracks. A new set of bolts are $288.00, installation is $500.00 for the set. I would have you tracks Three Days. I am located in Hanoverton, Ohio You can email or call!-330-831-0987 Thanks, Rays
  11. R

    TD 340 A pins

    Reggie, I can install you pins and bushing in your T340 Int Tracks. I have a trackpress can do any small trctors IH, JD, Case, AC, Cat,Komatsu, Up to D6 size. Also some Excavators. I can use your pins+bushings or I have a new set in stock. Will have to take the pads off, and replase the bolts. I...
  12. R

    Looking for a motor for HD6

    Tom, Do you need a344 or a 6000 series engine for your HD6. I have a good used 344 motor. Let me know, I will be glad to help. Thanks, Rays
  13. R

    allis chalmers hd4

    Mike, I think I can get new aftermarket rollers and track chain for a HD4. I will check monday and let you know. Thanks, Rays
  14. R

    HD 5 questions??

    Shawn, I can replace the pins and bushingin your tracks, or I can sell you the pins and bushings. It takes a very large press to do the job. Let me know if I can help. Thanks Rays
  15. R

    need lower track roller

    I need you to take some measurements off of your rollers, Like Diameter, Width, space between bolt hole centers. I may be able to come up with some for you. Let me know, Thanks, Rays
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top