(800) 853-2651
SHOP NOW

Recent content by reltor

Yesterday's Tractor Forums
  1. R

    Re: International 606 (d236 diesel) block heater

    bump
  2. R

    International 606 (236d diesel) block heater

    My tractor has a very old looking freezeplug type block heater in the right side of the engine. I don't see a screw in the middle. Just a rivet looking thing. Any idea how to remove it? Does anyone know of a good replacement block heater for this engine? Thanks
  3. R

    606 front pivot rebuild

    I think the problem lies in the bore of the axle. It was elongated at the ends and tight in the middle with the current pin. In fact I had to do some honing to get it through. I believe there was more slop with the original pin both in the bracket bushing and in the axle, that combined with...
  4. R

    606 front pivot rebuild

    The pin and bushing I put in were not IH parts. I had them made. The pin is slightly oversize 1.77". I did this because the holes were slightly elongated about .035", so I think I could take a little off the pin. I thought of making an offset bracket for the ball to the yoke, or a spacer for...
  5. R

    606 front pivot rebuild

    I am making progress on the front end rebuild of my 606, but have run into a new problem. I rebushed the front bracket and have a new pin that is 1.75" I can get the front axle on, but when I go to attach the link arms of the axle underneath, they are under extreme tension to get bolted...
  6. R

    International 606 diesel need help bleeding fuel lines

    I lucked out and did not have to bleed anything except the filter canisters. Thank you all for the help as I will know what to do if I get in deeper.
  7. R

    International 606 front pivot problem

    Thanks, that schematic from caseih.com really helped. I re-bushed my bracket and have a new pin and lock made from 4140 with a grease fitting, just like the original except I ran a grease groove back the the axle instead of just ouputting at the bushing. I found the small end of the steering...
  8. R

    International 606 front pivot problem

    I have got a 606 with a rigged together front pivot that appears to be a piece of pipe with pipe endcaps on it. The fit is sloppy the front of the tractor is too low and the steering arms are dangerously close to the oil pan. I can have a new pin and bushings made, but I don"t have any idea of...
  9. R

    International 606 diesel need help bleeding fuel lines

    Sorry, still figuring out how to post. OK, thanks for the help. One more question, when you say crack lines at the injectors do you mean up near the glow plugs on the head or where the lines come out of the injector pump?
  10. R

    International 606 diesel need help bleeding fuel lines

    OK, thanks for the help. One more question, when you say crack lines at the injectors do you mean up near the glow plugs on the head or where the lines come out of the injector pump?
  11. R

    International 606 diesel need help bleeding fuel lines

    I recently purchased a 606 diesel utiltity which ran really good, but would not start so well. Among other things 3 of the glow plugs were dead (so according to people on here I am lucky it started at all) I went through the fuel system, drained old fuel, cleaned sediment bowl, new filters...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top