(800) 853-2651
SHOP NOW

Recent content by resodziadzu

Yesterday's Tractor Forums
  1. R

    Is this bad for a PTO clutch?

    Make that "lessen wear and tear"
  2. R

    Is this bad for a PTO clutch?

    When I mow and get to the end of a row, I pull up the PTO clutch lever to disengage the haybine as I make the loop for the corner. Does this put increased wear on the clutch, esp. the throw-out bearing (if it has one)???! The tractor is a Hesston model 70-66. The purpose of doing this is to...
  3. R

    Balers to avoid like the plague

    Yes hex 1.251 bore, OD of 2.8346, sealed, spherical outer race which is .699 wide
  4. R

    Balers to avoid like the plague

    Round Balers Case IH 3450 and New Idea 484 use bearings on their rollers that are no longer available. If a bearing goes, you must buy a new roller, plus two new bearings for it. ka-ching..... ka-ching.
  5. R

    Round baler belts question

    How can you tell if round baler belts are 2 or 3 ply? I have one new bottom belt that came with a used machine, and want to buy 4 more that match.
  6. R

    new idea 484 baler

    Shoup has them, and at a better price than my other source. Thanks for reminding me of this source.
  7. R

    new idea 484 baler

    I am getting 4 out of 5 bottom endless belts, as one new belt came with our machine last year. One site on the net had a $ of 110 per. I am going to check around however. Anyone have a good source for belts? I'll pay a little more to avoid getting a P.O.S.!!!
  8. R

    new idea 484 baler

    How can you tell if a 484 New Idea round baler is an "earlier" or a "newer" model? It appears it makes a difference when ordering belts.
  9. R

    No Idea 484, CaseIH 3450 Rd. Baler question

    What size wire should be used to run power to the motor that moves the string arms on these balers. The old wire looks to be 10 gauge. To me that seems to be a bit much! I don't know what the amps are, but I did see a reference in the manual to a 5 amp fuse (which my New Idea doesn't have)...
  10. R

    NI 484, CaseIH 3450 Round balers elect. switch

    The New Idea mod 484 and the Case IH mod 3450 round balers have an electric switch that signals when the bale is at maximum size. Has anyone had to replace this switch, and if so, where did you get one?
  11. R

    Fermenting oats question

    Used municipal water, chlorinated, but not heavily. No detectable chlorine taste but will try some well water. As for feed store oats, i'd worry about its purity. I plan to plant some next spring (if all else fails) and grow to maturity.
  12. R

    Fermenting oats question

    Not quite an implements question but..... We make a soup (barszcz) out of fermented oats, but we can't get the oats to ferment anymore. When my mother made this in the 60's, 70's, the mix of oats, water, and a slice of rye would get really sour and stink to the high heavens. Now, I do...
  13. R

    Equipment transport and the law

    Brian in Ma, please do tell us about it, although I have an inkling of what may have happened!
  14. R

    Equipment transport and the law

    How far away from your farm can you drive unregistered equipment without fear of being pinched? I sure would like someone from Massachusetts to answer this.
  15. R

    Older, gray,New Idea 484 baler

    Will this baler operate on thin plastic twine? Anyone have a good source of parts?? Thanks.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top