(800) 853-2651
SHOP NOW

Recent content by rich o

Yesterday's Tractor Forums
  1. R

    feild hose

    anyone know were to get good used 2'' collapsible hose for liq manure transfere
  2. R

    kuhn moco rotor bering

    just discovered the bering on the outside of flail rotor is GONE. anyone ever replace one, it dosnt look conplicated but if anyone has any input or pointers i'd appreciate them ,, thanks
  3. R

    jd 336 timing

    i beleive my john deer 336 string baler is out of time, both the main and needle shears bolts keep snapping. this just started happening as i started baling second cut. 3000 bales of first crop and it didnt even miss a knot. ive had timing issues with a nh baler and it seems to make sence that...
  4. R

    kuhn f300 moco

    wile mowing today in a flat smooth feild , a sound developed which sounded like a rattling shroud somewere. upon further investigation when i raised the cutterbar and bra, the whole center of the cutterbar was violently flexing,the likes of wich ive never seen or could imagine could happen...
  5. R

    ford 8n

    recently wile raking on a moderate down hill slope my newly aquired 8n, through itself out of gear, creating a very dangerous situation for my 16yr. old son operating it. gravity took over , the brakes seemed to do nothing but help with the acceleration. i know this because it happened to me...
  6. R

    leaky fuel line

    i checked for cracks ,did not see any, it has a ferrole before the flare, it seeme maybe the ferrole has been compressed maybe to many times. i dont have much extra line but may be able to pull a bit from a small verticle drop the line takes off the injector pump. what type of tool will flare...
  7. R

    blue exhaust

    help!!! my terrible blue smoke has stopped ,but has been replaced with haenous white /greyish smoke,very heavy., i hope the neighbors dont call the epa. it has also lost significant power and seems to be knocking and ideling rough, this has all happened after 7+ hours of light tedding on flat...
  8. R

    blue exhaust

    just put my engine rebuild of my massey 65 to work and it seems to be smoking bluish ehhaust, i thought it would burn off but it has not, whats up. i did pistons/ rings /sleeves / bearings /valve job.also set the timing to what i thought was done correct. why does this colored smoke appear
  9. R

    leaky fuel line

    , i have a stubborn leak in two different connections in my fuel system. both in lines coming from the filters, they seem to be thghtened all the way down, possibly leaking from the line were the compression nut goes over. is there a seal or compound that may cure these stubborn leaks? thanks...
  10. R

    mf65 valve timing

    im just finishing up my rebuild , could anyone give me the lowdown on setting the valve timing steps , a simple condensed version. will i need to do an assembly timing than retime it after its hot?. because the tank is inastalled over valve cover, just could use a few pointers. the engine ie...
  11. R

    engine block reconnection to clutch housing mf65

    welding man, good advice, backed it off visually lined up splines and grooves, used longer bolts to act as guides walked it in slowly, but with only about a pinkys width left ,heard a cracking sound and could no longer turn the crank. backed it ann off and pulled the block assembly away and...
  12. R

    engine block reconnection to clutch housing mf65

    ive replaced the pilot bering and it was identical to the one i removed, i also took care to make sure the 2 clutch disks were centered when i put the clutch assembly back together, i had reused the existing clutch disks because they still had plenty of life to them
  13. R

    engine block reconnection to clutch housing mf65

    i still have about 3/4'' til the dowels engage but the bugger just wont go, i thought it was possibly in just a bit deeper
  14. R

    engine block reconnection to clutch housing mf65

    does anyone have any good tricks to reconnect the block adapter plate to the clutch housing on my massey 65. the block is all lined up nice and square but just wont go the last inch, i cant tell if the clutch spline is catching on something, ive turned the crank in hopes of mating the spline but...
  15. R

    potato digger

    any ideas on a homemade potato digger
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top