(800) 853-2651
SHOP NOW

Recent content by Riversea

Yesterday's Tractor Forums
  1. R

    IH 684 Valve adjustment

    Hi Everyone. Just finished rolling the tractor together after replacing the rear seal, clutch, flywheel resurface, etc. Before I install the engine shroud, I thought it would be prudent to check / adjust the valve clearances. The factory spec is .012 for intake and exhaust respectively, with...
  2. R

    NH 851 Round Baler

    I appreciate the explanation. Where is the upper attachment point for the spring? I went to that NH website but the diagram does not show where the spring attaches. Possible that you can take a picture of the correct set up? Thank you.
  3. R

    NH 851 Round Baler

    Ouch! That's like $100 US. Made 20 decent bales though.
  4. R

    NH 851 Round Baler

    The spring you see on the picture is something that I came up with - in the absence of a diagram that shows the proper location of a tensioner. There is a bracket (with a bolt and a "key hole") that looks like a spring or tensioning device should pull it up. After looking for a suitable...
  5. R

    NH 851 Round Baler

    Hi There; I am new to baling and just purchased a well used 851 baler. Works not too bad, except for the drive side (left side) belt "derailing". The belt drives the (pardon my ignorance of technical terms) upper conveyor. I think the OE belt is a double V (two groove pulley), but the previous...
  6. R

    Re: Oliver 1250

    Do you have any suggestions on where I might start looking for the cause of the hitch settling when the tractor is turned off? Thanks.
  7. R

    Re: Oliver 1250

    The hitch will settle after the tractor is shut off. I still can't figure out how to see your email address. Can you put it into your Profile? Thanks.
  8. R

    Re: Oliver 1250

    Nope. Not there. Can you provide the information in a post? Thank you.
  9. R

    Re: Oliver 1250

    I just tested it from the link provided. Had to sign in to my own (other) email to send it. It worked. Please try again, or post your email. I could really use the info. Thanks.
  10. R

    Re: Oliver 1250

    For the bouncing 3PH problem. My email is: [email protected]
  11. R

    International 230 Windrower

    I appreciate you taking the time to send this info.
  12. R

    Oliver 1250

    Anyone with "New Old Stock" sound as if he may have experience with Cockshutt Tractors. I have a 1250 Gas. Beautiful tractor. Bought it 15 years ago at an auction for $5000 - with Loader from the original owner. 2000 hrs. This tractor has always suffered from a "bouncing" 3 point hitch. The...
  13. R

    International 230 Windrower

    Hi There. I hope I am not breaking any rules by asking a question about a Swather on a Tractor site. I just picked up an IHC 230 that (apparently) has a C - 153 engine. I understand that this engine is similar to the C 153 that has been used in Farmall and IHC Tractors. I think I have see...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top