(800) 853-2651
SHOP NOW

Recent content by rnccen

Yesterday's Tractor Forums
  1. R

    Need help with Farmall M 12V wiring

    OMG .. it never dawned on me to see if the switch was on...Ill have to go try.
  2. R

    Need help with Farmall M 12V wiring

    There is a foot lever down at the base that has a 2 post push button switch that I presume is the starter button to activate the circuit, which I noted on my diagram as push button starter. Looking at the parts section here, it looks like what I call the kill switch in my diagram is actually...
  3. R

    Need help with Farmall M 12V wiring

    Good morning, well either I am missing something or I messed something up, I used the above images as guides and still nothing, no click or start. Battery is good, push button start is good, solenoid is good, engine will crank if I just connect positive and starter to push button start. Here...
  4. R

    Need help with Farmall M 12V wiring

    Thank you all for your assistance, I will tackle it tomorrow and advise of success. Appreciate the assistance. The Alt. is a Delco
  5. R

    Need help with Farmall M 12V wiring

    Afternoon, I have a new Farmall M that was converted 12V 1 wire but the prior owner did not finish the wiring so it would be started. Would someone kindly fill in the wires, as I have searched google and forums without much luck. I have found ones with the regulator but not one with a...
  6. R

    135 lift arms fine with no load, won't lift with a load

    Sorry for the very likely similar post to others but here goes. 68' Massey 135 diesel, lift arms raise / lower with no load but when they raise they do not do up to the highest point (basically 3/4 way). I have the service manual but for some reason I can't quite wrap my head around it to...
  7. R

    MF 135 Fuel Tap / Shut off

    The screen is rusted out and the knob to open/close is gone. If the screen is replaceable do you know where I can find one? I can make a knob probably.
  8. R

    MF 135 Fuel Tap / Shut off

    I have a MF 135 diesel (Perkins) that has a brass fuel tap block with a clogged rusted metal screen and a male end that goes to the fuel lifter pump found this image on an oder post from 2017 that has the same style. All the fuel taps have a female receptacle that goes to the lift pump from...
  9. R

    Urgent help. 35 hydraulic filter

    Napa does not have the lift pump filter, here is a link to their catalog for MF. [urlhttp://nfhconnect.com/OfflineCatalog/Off-Highway-HD/1573/#zoom=z[/url] As long as you are not using the hydraulic pump, then you should be ok to drive it home as that system would not be in use.
  10. R

    Need opinion please

    Just wanted to thank PTFarmer for coming out and helping resolve my issue with the 135. Greatly appreciated...back up and running. In addition, thank you to Rockepg for his assistance via this forum. Great resource....thank you again.
  11. R

    Need opinion please

    The fluid barely gets up the stand pipe...I suspected the pump has gone bad and in need of a rebuild / replacement. It was working just prior to replacement of the lift piston which is what I was not sure about. not sure if I can get just a seal kit or if I need to redo the whole pump, not...
  12. R

    Need opinion please

    https://www.youtube.com/watch?v=WGBW7y0Nv8g The link is to a video I took, thought the new relief valve may have been bad, but there is nothing coming out of it. Pump is moving but still no pressure.[/url]
  13. R

    Need opinion please

    Well I replaced the control valve in the lift pump per the manual, put it all back together and back in tractor, put new oil back in again. Cover back on, etc...still nothing on the arms. draft and position are in up position, I can lift the arms up by hand there is no resistance, same in...
  14. R

    Need opinion please

    ok not sure what happened to my 1st reply...but anyway...drained all the fluid out, took the cover off again. The roller arm when I push toward the front of the tractor has resistance then at a point clicks. When released, the arm goes back in. I can move the arm in and out...not sure how...
  15. R

    Need opinion please

See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top