(800) 853-2651
SHOP NOW

Recent content by Rock2001

Yesterday's Tractor Forums
  1. R

    Super M clutch slip (main or M&W)

    Honestly I'm not 100% certain the PTO was still turning. I think the last time I did notice it still turning, but unfortunately at the time I wasn't focused on that so I could be wrong. I have one more field to cut so I can pay more attention, but it is not nearly as thick or hilly so I don't...
  2. R

    Super M clutch slip (main or M&W)

    I had the first real test for my Super M project, and unfortunately it failed. I was mowing my field, and after a few passes it stopped moving when mowing up a hill of very thick grass. I turned off the mower and still it wouldn't move. I gave it about 40 seconds to rest and it went up the hill...
  3. R

    Water pump packing

    I've looked at the hardware store previously and the only packing I've seen is around 3/32 width. What size would I be looking for?
  4. R

    Water pump packing

    I have a bit of a leak on a Super M water pump at the tip. I guess the packing is not doing the job anymore. I was looking online and if I understand what I need, I see that a piece of packing is about $25 and you need 3 of them? Really, $75 to repair it? Is that right? Is there any cheaper...
  5. R

    M&W clutch removal

    Thank you. More reasonably priced than I expected.
  6. R

    M&W clutch removal

    Ah, yes you guys are right. I see a small nub on the washer where there was an inner tang. Must have broken off. Great.
  7. R

    M&W clutch removal

    Thanks. That thin spiral was almost invisible to me. :) I finally found some seals that seem like they should work (as long as the shaft isn't too worn). I threw it back together. Not ready to test it all yet, but I had one last question. The nut and tanged keeper at the outside. I should bend...
  8. R

    M&W clutch removal

    OK I got back to this. I ended up getting a slight gap between the cover and backing plate and cut the bolt there. It was frozen into the cover, as once the cover was off I was actually able to unturn the remaining threaded stub with just fingers. I took out most of the other parts. I got the...
  9. R

    M&W clutch removal

    Yeah there is a plate that the cover is bolted to. In the side picture you can see where I stuck a prybar between the two and it bent the plate. The bolt doesn't go into the transmission cover as I've had that off previously (if I knew I should have messed with this bolt then). I haven't tried...
  10. R

    M&W clutch removal

    I don't see any set screw. The only thing at the bottom seems to be an inspection hole, with no screws inside. Here's some pictures, although I've put some stuff back on temporarily as I just broke a brake line on my car and need to kick this out of the garage for a bit. Not much to see but it...
  11. R

    M&W clutch removal

    Thanks. It doesn't seem to be stuck on the brake band as I can pull the edges of the housing away from the backing plate everywhere but the pivot bolt. I tried to pry between the two in that area while wiggling the housing, but no dice. I think I bent the backing plate. If the housing should...
  12. R

    M&W clutch removal

    But I'm stuck on step 1. How do you remove that long bolt? I used a pipe wrench on the shaft, which already seems like it can't be the right way. But the bolt snapped, so if it is threaded in at the other end then I'm in a world of trouble.
  13. R

    M&W clutch removal

    I bought a SuperM that I've been repairing. It's going, but it's leaking oil out of the M&W hand clutch. I presume there is an O-ring that needs replacing? I took off the housing bolts but I can't get the housing off. Feels to be stuck around the handle shaft area. Is it threaded somehow and has...
  14. R

    Super M carb broken tube

    Ooooo, $10. Nice, thanks. The drill needed doesn't seem too small. I have many much smaller. The easy out, yeah that is too big. I'm used to wanting to use them on large bolts and complaining they are always too small, so I got a biased sense of how small they were. I tried to tap a small...
  15. R

    Super M carb broken tube

    I took a look at the carb for my Super M project. When I took it apart I found the little tube that sticks out between the halves was slightly bent. Tried to see what was up with it and it quickly broke off. I did some searching and found some info for the Cub, and what they call the idle tube...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top