(800) 853-2651
SHOP NOW

Recent content by roger landers

Yesterday's Tractor Forums
  1. R

    4430

    Thanks for the info , i have adjusted the aneriod about 25 clicks as explained,and it has made a world of difference. They should have been like this from new.
  2. R

    merry christmas

    Merry Christmas to all, Thanks for the kind folks that have replied to any of my questions . down under we are 18 degrees cel at 8am in the morning . summer time over here thou. Thank again Merry Christmas
  3. R

    Diesel tractor winter storage

    I have a mate that has Case 155 ,same as a NH tm155 . It does baling all harvesting season then is parked up over the late autumn to next season. After about 4000 hrs ,(6-7 years old) the injectors and turbo started to fail. The mechanic said that condensation/rust on the injectors etc from...
  4. R

    sway chains or three point linkage stabilisers- 4430

    Taken a photo ,but camera doesn't want to talk to computer. I see that the block are in the cat one position. Holes for the cat two position face towards the front so missed them . cheers
  5. R

    sway chains or three point linkage stabilisers- 4430

    I will take a photo and put on here . A picture will show the problem better. Each side has about 1.5 inchs gap before the lower arms meet the sway blocks. The mower could have wide attachment points compared to what was put out in the 70"s
  6. R

    sway chains or three point linkage stabilisers- 4430

    Hi , Is there anything that can be retro fitted onto a 4430 three point linkage arms ,to stop the excessive sway when I has a mounted hay mower on . JD is its wisdom choose to use the mounting block type system ,which is my opinion was a pretty poor set up . Did the latter new gen tractors...
  7. R

    Air popping back through intake...

    It could be the carbon you have talked about . I would also check the tappet clearances as well. Then give it some work roger
  8. R

    4240 safety swith

    has the replacement safety switch been put in correctly . They usually have a plastic tool to measure the shims needed ,to get the right distance in or out when screwing the switch in.
  9. R

    4620 Lights - Wiring Question

    on my 4430, I had to get a 1/8 drilled into the item number 22 ( if similar to a 4430 ) I used the pressure switch part number that the friendly folk from here gave me . I think it was from 40 ,or 50 series.I took the fitting with the switch to the local engineer to drill and thread to suit...
  10. R

    JD 2140

    Thanks for all info cheers Looking into a 2nd hand block ,or fitting the bigger bushes that run the standard bearing on the balancer shafts . roger
  11. R

    JD 2140

    Hi , I have a jd 2140 that the balancer shaft has eated out the bearings and stuffed the block . What other jd engines fit in a 2140 . Being In New zealand , i would quess that it is euro sourced rather than usa, if that changes anything. What size engine did these tracors use? regards roger
  12. R

    nh ts100- left hand reserver.

    Is there any way to slow delay the reserve - forward time . I would be only trying to delay it by a few seconds . The tractor has had new sinhco "s on the forward reserve ,and by slowing this down some ,it may help with the life of this part. The operator can play a part in the wearing out of...
  13. R

    Pros Cons 359T vs 404 engines

    John Deere had moved on from the 404 by then , to the 466.Poor low end torque was the main issue for this motor.The 359T was also being produced by that stage in far greater numbers ,so probably far more ecomonically to build that engine ,especially as the 404 needs some development to overcome...
  14. R

    4230 or a 4040?

    Di the 4040 have the 404 engine? ,and then the rest of the 40 series the new at the time larger version 466 engine?
  15. R

    4440 tractor and batwing problem.

    My first guess , that the pto shafts are to long . Both the outer and inner need to be shortened so if you go into a dip or something similiar ,the shaft has room to shorten.An over long pto will bend a pto shaft pretty easy ,as something has to "give" If this isnt your problem , the others have...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top