(800) 853-2651
SHOP NOW

Recent content by Roger Missildine

Yesterday's Tractor Forums
  1. R

    Transmission Oil / Fluid for MF202 Industrial

    Hey all, Got the 202 up and running. Need to change the tranny fluid. None of the info I have list"s what to use. What do ya"ll use. Just a note, I don"t have an internal pump, no lift arms, no PTO, just the tranny... Thanks, Roger
  2. R

    MF 202 Industrial clutch release bearing

    Hey guys Update on the release bearing. Ears wouldn"t sit on 2X4"s without rocking, kinda small, but I was able to sit it in the vise with the carrier facing down and using a brass drift, a couple of good stern smacks, it popped right out. Got the carrier cleaned up, new release bearing ordered...
  3. R

    MF 202 Industrial clutch release bearing

    Thanks for the replies guys. P.T., I was thinking along those lines, only not much for the ears to catch on, afraid of breaking them. Tim, sounds like your method may work, I just didn't want to smack it to hard, but I'll give it a try this evening when I get in from work. Forgot to mention this...
  4. R

    MF 202 Industrial clutch release bearing

    Thanks for the replies. Steve, looking at what they offer here for my tractor, the bearing is seperate from the carrier, so, it needs to come off. R.F, I was thinking of the press off aspect, only it doesn"t have a lip on the inside to set a drift on for the press. Don"t want to break off the...
  5. R

    MF 202 Industrial clutch release bearing

    OOPS!! Forgot to post pics... Here we go.
  6. R

    MF 202 Industrial clutch release bearing

    Posted this down on the Massey Ferguson board too. Hello to all, and thanks for all the help so far on "Bull" the 202 Industrial. Got the bottom end of the engine back together and waiting on the valve overhaul kit so I can get the head in the shop, hopefully next week. Thought I"d check a few...
  7. R

    MF 202 Industrial clutch release bearing

    Hello to all, and thanks for all the help so far on "Bull" the 202 Industrial. Got the bottom end of the engine back together and waiting on the valve overhaul kit so I can get the head in the shop, hopefully next week. Thought I"d check a few things while I"m waiting and decided the clutch...
  8. R

    Continental Z134 Rear Main Rope Packing

    Thanks for the replies folks. Yes I was referring to the "string" packing. I knew to pack it down, good and tight, but the old sting had what looked like some sort of sealer on it, kinda crusty. So, I was just wondering. Hope to get the crank and cam in this evening... Thanks again, Roger
  9. R

    Continental Z134 Rear Main Cap Rope Seal

    Posted this up on the Repair Tips forum too, any info appreciated... Hello all, Finally getting ready to put the MF202 engine back together. Concerning the rear main cap rope packing,(between the rear main cap and block), I"ve read, but can"t find the post where someone stated that they coated...
  10. R

    Continental Z134 Rear Main Rope Packing

    Hello all, Finally getting ready to put the MF202 engine back together. Concerning the rear main cap rope packing,(between the rear main cap and block), I"ve read, but can"t find the post where someone stated that they coated the rope with gasket sealer prior to packing it in the slots. Just...
  11. R

    Continental Z134 valve guide installation

    Thanks Steve, and everyone else. I'm pretty sure that the #4 exhaust is worn because it wasn't a little leakage, it was a pretty constant drip. After setting overnight, I checked the combustion chambers and they were damp with solvent, so a valve job is in order anyway. And since I'm gonna be...
  12. R

    Continental Z134 Valve Guides

    Thanks for all the replies guys. Yes, I know engine machine shops are high, but there are a couple in the area that have been around for many years. One is a tad cheaper and I"ve had work done by both with no complaints. As far as boring the guides and having replacements installed, well I"d...
  13. R

    Continental Z134 valve guide installation

    Thanks for the info Dick, At my old job, I had access to a lathe and vertical mill and could have made the tool. Unfortunately, I don"t have that any more. I know the repair manual states two different heights for the intake and exhaust guides, and was thinking along the lines of the 6" steel...
  14. R

    Continental Z134 valve guide installation

    Well hey to all again. Posted this on the Massey forum too hoping to get some advice. Got the head and block cleaned up on the MF202 this afternoon. Did the liquid check on the valves by filling the intake and exhaust ports in the head with cleaning solvent. After about 30 minutes, went to check...
  15. R

    Continental Z134 Valve Guides

    Well hey to all again. Got the head and block cleaned up on the MF202 this afternoon. Did the liquid check on the valves by filling the intake and exhaust ports in the head with cleaning solvent. After about 30 minutes, went to check and found a couple of the exhaust valve guides leaking...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top