(800) 853-2651
SHOP NOW

Recent content by ronb.vip

Yesterday's Tractor Forums
  1. S

    LUC Mag and timing questions

    pulled the mag off of my LUC engine to get rebuilt and now I am ready to put it back on and set the timing. My owners manual says to turn the crankshaft until spark mark on flywheel lines up with lines on timing hole with No. 1 piston on compression stroke. My question is...which cylinder...
  2. R

    becoming a police officer

    As a former Police Officer in Toronto Canada, I would say that temperament and conscience must be both in good shape. As a person with disceretioary powers, one must understand that prevention is your first duty, to redirect someone on the right road in life far exceeds apprehensio and...
  3. R

    think I'll sell my case 310B B/L

    Have some health issues and need to do more around my property, so I will seel my Case 310B roundnose. I've replaced spindles,rebuilt P/S ram, new hoses,front oil seal,pulley and shaft for hyd pump, clutch pedal and brake actuator,new bucket (still have original case one though),new rams...
  4. R

    shuttle shift gasket leak.

    I have finally got my 310B 1/2 assed finished, and I was checking fluid levels and found that the shuttle shift level was not showing. I filled it to the top level, and moved it and parked it. Today, I moved it and went 80 ft, and noticed a trail of fluid. It seems to be RUNNING out of the bolts...
  5. R

    how to make trail type stone picker

    I used to have a stone picker, but sold it and now want another one the same. It was dragged behind the tractor and had rods that moved sideways when the hit a rock, and the rock would be carried bt the earth and put the rock on a platform, I think, It kind if looked like a bale buncher rig...
  6. R

    Front pulley oil seal replacement on 310B

    Is there a set distance specified anywhere? i have placed the seal as far back as it would go till it stopped naturally, but I'm wondering if this is too close to the slinger plate?? Thanks Ron
  7. R

    Front pulley oil seal replacement on 310B

    I have a front pump and the heavy duty pulley on my 310B. Ihad to change the belt and decided to do the oil seal at this time. How far back should the oil seal be placed on the crank, all the way to the plate or slightly forward on the shaft? Thanks Ron
  8. R

    loose pulley on crankshaft

    A buddy came over and 6 bolts later the pulley was off. Sorry I troubled you, but thanks Ron
  9. R

    front pump pulley on 310B-how to remove???

    I have a Case 310b roundnose B/L. The key in the front crank is sheared and has to be replaced, but I can't get the pulley out because the rad supports and bolster are in the way. The machine was badly abused and most of the 3/4 bolts are sheared off holding the side frame and loader on. Has...
  10. R

    loose pulley on crankshaft

    I think a heavy piece of wood hit the pump shaft when it was running, or metal fatigue , the machine is over 50 yrs old. However, I thought the pulley should come out but maybe it's a 430 engine in the 310B. Short of torching the rad supports, I don't have an answer.....What about drilling and...
  11. R

    loose pulley on crankshaft

    Well, thanks , but I can't take off the front cast piece because bolts have broken off that hold the loader on and the removal would be a lot, so it's an improper fix, but that's the route I must follow, although I don't want to. But,I thought if I drilled a hole opposite the key way and into...
  12. R

    loose pulley on crankshaft

    The key is sheared, and the pulley can't come off without major work and I was hoping there might be a way to lock the crankbolt by some other means as I don't want to spend the summer tearing the whole machine apart....any ideas??? lock washer (external tooth, loctite (red)????
  13. R

    loose pulley on crankshaft

    Picture of pulley and keyway
  14. R

    loose pulley on crankshaft

    Thanks for the reply, but don't you have a keyway to hold the pulley to the crank or is it held by the compression of the nut? I'll show you a pic of the nut on mine. Will your pully spin freely if the nut is undone, without the crank turning?
  15. R

    case 310B pump coupler

    I have an abused Case 310B B/L. The Crank pulley was assembled without the four buhings in the pulley end coupler connection, the key is sheared on the crank, the end nut (square 1/2' hole to tighten and undo is ok but the pulley wont pass by the two cast pieces in front of it....so how can I...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top