(800) 853-2651
SHOP NOW

Recent content by Ronie

Yesterday's Tractor Forums
  1. R

    Settings for the 165 lift cover

    an I ask what service manual you hve, mine only list the parts breakdown in the hydraulic section? This post was edited by Ronie on 09/10/2023 at 07:17 pm.
  2. R

    Settings for the 165 lift cover

    hanks for the reply. I should have been clearer about what I was looking for, I was needing the clearance between the plunger and lever and the measurement for the pressure controll vave. I used .002 for the plunger and I measured 35mm from the bottom of the pressure control to the crown of the...
  3. R

    Settings for the 165 lift cover

    Can someone point me to the clearances and measurement for setting up the lift cover. I found a good video on the procedure but need the settings, my service manual doesn't list them. I also have the drawing for the tools. The casting is E2 B4 Thanks for any help you can give me.
  4. R

    MF 3165 hydraulic pressure valve

    I found where that roller goes.
  5. R

    MF 3165 hydraulic pressure valve

  6. R

    MF 3165 hydraulic pressure valve

    One last part I haven't figured out, any ideas? This post was edited by Ronie on 09/07/2023 at 12:22 pm.
  7. R

    MF 3165 hydraulic pressure valve

    I got it figured out.
  8. R

    MF 3165 hydraulic pressure valve

    I picked up this 3165 and the lift cover had been pulled off. The lift cover was disassembled by someone and a lot of the pieces were bent up, like the lift cover had been dropped.. I've got everything as straight as I can and mostly put back together but I can't figure out where the tube off...
  9. R

    Newest addition

    Nice!
  10. R

    47 Case VIA Hydraulics

    I will, thanks.
  11. R

    47 Case VIA Hydraulics

    Never mind, it's working now.
  12. R

    47 Case VIA Hydraulics

    Hi, new here and I have a problem. I have a 47 Case VAI with an Eagle hitch and the lifting arms will not go down with the pump running, when I shut off the motor and move the up/down lever to down position they go down fine. Also with the pump running and I move the lever to the down position...
  13. R

    47 Case VIA Hydraulics

    Looking for some help with a high pressure hydraulic system. I purchased a 47 Case VIA and it has a high pressure pump on it. Someone has taken off the hydraulic lines and I can't figure out where the return goes, there's no inlet on the torque tube for it. any help would be appreciated...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top