(800) 853-2651
SHOP NOW

Recent content by RONZ TRACTOR

Yesterday's Tractor Forums
  1. R

    injector

    i need soom help i have a 300b commercial tractor i pulled the head to replace the head gasket but can"t get the injectors out any ideas would help.thanks.
  2. R

    repair manuel

    i need to find a repair manuel for my farmall A if any one could point me to a site. thanks
  3. R

    farmall A lights

    ok thanks for the info,would you know where to go for a repair manuel ? also what type of fluid goes in the gear train.
  4. R

    farmall A lights

    if you remove that half moon cover will you see the brake band
  5. R

    farmall A lights

    how are the lights operated? i see a switch with b,d,h,l,on it is this the light switch.also my left brake won,t hold linkage looks like it,s moving,is there a adjustment?.thanks
  6. R

    engine lift

    i need to pull the engine on my 640 the engine lift in the book looks like it mounts to head but i can't tell how.does any one know how or a different way to do it.
  7. R

    per 640 block question

    i went to look at this 740 the engine sounds ok and it has some sheet metal i could use but the rest is pretty rough.i noticed the steering and front end looks different and there looks like they added a frame in front how does the 740 differ from my 640?
  8. R

    640 BLOCK

    thanks for the info sorry about the caps didnt realize thats what it meant.
  9. R

    640 BLOCK

    I HAVE A 640 WITH A 134CU EAE6015H WITH A BAD BLOCK WILL A BLOCK OUT OF A 740 (SERIAL-70941) FIT ? THANKS FOR ANY HELP
  10. R

    JACOBSEN G10

    DOES ANYBODY HAVE ANY IDEA WHERE I COULD GET PARTS INFORMATION ON A JACOBSEN G10 TRACTOR?
  11. R

    JACOBSEN G10

    I HAVE A JACOBSEN G10 TRACTOR. I'M LOOKING FOR A BRAKE MASTER CYL NEW ,REBUILT OR REBUILD KIT.
  12. R

    hole in block

    IF YOU CAN SHARE YOUR PHONE # OR E-MAIL WE CAN TALK ABOUT IT MORE.
  13. R

    hole in block

    EAE-6015-H
  14. R

    lower draft arm

    on my 9n the rt lift link broke i want to remove it to weld up.the nut seems to be frozen on the shaft there seems to be some sort of support plate that holds it on to the rear axle housing one nut holds the plate tight i removed it and the plate came loose but won't come all the way off the...
  15. R

    hole in block

    i guess i ran it a little to long with that rod knock. so i'm looking for a block or engine for my 55-ford 640 134 cu in.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top