(800) 853-2651
SHOP NOW

Recent content by Rottenground

Yesterday's Tractor Forums
  1. R

    John Deere 60 power trol

    Thanks for the information I will give it a look
  2. R

    John Deere 60 power trol

    1954 60 power trol it has external hydraulics plumbed in but not through the back factory cylinder connection lift works fine going up but the pump makes noise when u let it down like it's pumping against a restriction but it does lower
  3. R

    Dresser td7e

    thanks Jim for the reply how do I email you when I click on you name your email doesn't show up
  4. R

    Dresser td7e

    I need an expert on dresser td7e I am looking at one to buy an have some questions
  5. R

    John Deere early styled b 1946

    Looking to loose weight on the radiator Wondering what aluminum radiators u guys are making work thanks for all the info
  6. R

    John Deere 320

    Hey guys what fluid goes in the trans and final drives on a 320 I think it's a 57 model I think it had 8090 in it but I want to make sure thanks
  7. R

    Dltx 51 nozzle

    The nozzle in a 51 has a little tube made on the side of the nozzle and the top of the nozzle that goes up into the throat of carb is angled. Should the little tube go towards the choke plate or throttle plate
  8. R

    Early styled b block

    Yes block measured 4.502 pistons measured 4.748 I am gonna a take it to machine shop and let him ponder on it
  9. R

    Early styled b block

    I have an early styled b and was wonder if I can bore the block enough for some later B 90 over pistons. I measured it its roughly about .250 didnt know how much u could bore them early blocks b1783r thanks
  10. R

    Angle iron -pressed steelJohn deere B

    Will a straight front end non rollomatic fit from an angle iron frame B fit in a late John deere pressed steel frame. Thanks
  11. R

    Late Jd B Identification

    Has no waterpump has 4 round holes in wheels and 4 holes for wheel weights so in assuming they are 8 hole wheels there is a hole in the pedestal I think for the choke rod tractor didnt have a choke rod when purchased. I'm gonna say its probably around a 51 model?????
  12. R

    Late Jd B Identification

    Late Jd B identification tractor had no tag its square axle straight 6 six trans. Reduction cover has a drain and fill also two pc shifter tower any help narrowing down its year for a friend thanks. Any casting number I can get to get closer year pinned down thanks
  13. R

    9 bolt 38 wheels

    I have a JD A with 9 bolt pressed steel wheels will 9 bolt wheels say off a 1066 be the say bolt pattern and fit on my jd hubs or will any 9 bolt wheel fit thanks
  14. R

    1946 John Deere a

    I have the same tractor as you. Mine is bored, has late A aluminum pistons. My head has been milled .150, I gasket matched the ports on the head and manifold and barely polished it. Mine has a stock gas manifold, stock cam, and stock rockers. It runs good, starts fine, made about 115 psi of...
  15. R

    1946 A Upper pedestal bushing

    I am wondering if someone has made a bushing due to wear. The bushing looks to be made out of brass, pressed in down in the pedestal and holds the eccentric not a bad idea if someone done it in the field
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top