(800) 853-2651
SHOP NOW

Recent content by RSFARMS

Yesterday's Tractor Forums
  1. R

    900 FORD ROW CROP

    Definitely not trying to upset anyone here that i am asking for help from sorry for the caps but i replace the plate on one side of the gasket the other side is the pump end housing and has a resessed mating surface.
  2. R

    900 FORD ROW CROP

    ANYTHING ELSE YOU MAY KNOW THAT WOULD CAUSE THIS TYPE OF PROBLEM THAT I MAY NEED TO CHECK ? INSTALLED ALL NEW GASKETS SPRINGS & SEATS FRONT SEAL & SHAFT IN PUMP THIS LAST GO STILL SAME PROBLEM.
  3. R

    900 FORD ROW CROP

    NO EVERYTHING ELSE IS WORKING FINE JUST BLOWING THAT GASKET AFTER SEVERAL HOURS OF RUN TIME USING THE 3 POINT HITCH. THANKS FOR THE INFORMATION ANY GOOD SOURCE FOR A GOOD REPLACEMENT VALVE?
  4. R

    900 FORD ROW CROP

    CAN ANYONE TELL ME IF A 900 FORD HAS A HYD. RELIEF VALVE AND WHERE IT IS LOCATED HAVING TROUBLE WITH IT BLOWING THE GASKET ON THE BACK END OF THE PISTON PUMP. ANY HELP IS APPRECIATED. THANKS IN ADVANCE
  5. R

    5000 FORD

    THANKS IS THERE ANY THING TO BE CAREFUL OF WHEN SPLITTING THE TRANS FROM REAR
  6. R

    5000 FORD

    HAVE A 5000 FORD TRACTOR RELEASE BEARING LOCKED UP & BURNT FINGERS OFF PRESSURE PLATE . THE QUESTION IS THE PTO SHAFT & DRIVE HUB SPLINES ARE ALL BUT GONE HOW DO YOU GET THE SHAFT OUT OF THE TRANS. THANKS FOR ANY HELP IN ADVANCE.
  7. R

    1466 HITCH QUESTION

    THANKS FOR THOUGHT BUT THE LEVER IS SPRING BACK TO HEAVY HARD NOT JUST A SLOW VIBRATION DOWNWARD
  8. R

    1466 HITCH QUESTION

    WORKING ON 1466 HITCH WOULD NOT LOWER REMOVED CENTER LINK COVER LEVER HAD TRIPPED OVER SENSING LINKAGE PULLED BACK & RESET. QUESTION IS DRAFT CONTROL LEVER SPRINGS BACK TO HEAVY WHEN MOVED TOWARD LIGHT WHAT COULD CAUSE THIS ISSUE?
  9. R

    Colby 560 fit & finish w/ plan to finish this week.

    BEEN FOLLOWING YOUR POSTS A VERY GOOD LOOKING TRACTOR WITY A LOT OF QUALITY WORKMANSHIP.THIS IS ONE TO BE VERY PROUD OF.
  10. R

    Canister next to gas tank?

    I HAVE ONE ON MY H THAT IT HOUSED GAS FOR STARTING THAN AFTER WATER TEMP GOT UP IT WAS SWITCHED TO KEROSONE IN THE REGULAR TANK.
  11. R

    706 TA replacement

    A TA INSTALL IS A MAJOR JOB BUT IF YOU HAVE SOME TRANMISSION EXPERINCE IT CAN BE FIGURED OUT BUT I WOULD ALLOW AROUND $2000.00 FOR THE REPAIRS.
  12. R

    rear tires h farmall

    THANKS FOR THE INFORMATION TRYING TO KEEP IT ORIGINAL AS POSSIABLE. MAYBE LOOKING FOR A SET OF RIMS ONE IS IN BAD SHAPE.
  13. R

    rear tires h farmall

    can any tell me if a h came with 36" tires on the rear or have they been changed
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top