(800) 853-2651
SHOP NOW

Recent content by rsk

Yesterday's Tractor Forums
  1. R

    Early G-1000 Vista hydraulics

    what is the hyd.doing or not doing,?
  2. R

    New F250

    Bought F350 dually with 6.7 loaded 12000lb pulling tractor on trailer truck didnt even know it had a load.
  3. R

    max rpms for 504 diesel

    I agree lp is not the same as diesel in setting them up.We installed extra valve springs to keep from floating the valves,had it on the dyno 325hp at18lbs boost.
  4. R

    max rpms for 504 diesel

    I run 2800 on turbo charged 504 lpgas,with no problems so far.Been pulling it for 3 years now.
  5. R

    2055 Oliver Tractor

    I have a 1050 lpgas that I believe is a 2055,It has a Minn.Moline tag but green paint was under the yellow paint.Had holes for the oliver side emblems and trim.We painted it back green and decaled it as an Oliver.My son and I pull it in farm stock class,with the turbo and other little things...
  6. R

    big tractors

    Does anyone else pull something beside antique tractors.We pull in the 12000 farm stock,6000 light super stock.Would like to hear from others.Thanks Rich
  7. R

    1855 chain coupler

    Chain broke on 3speed coupler while chopping today would 3speed lockup cause this or chain just old and tired.Everything was going good until then no viberation or anything.Thanks,rich
  8. R

    Big Diesel

    I,have a friend with 585 at 900 cubes turbo,custom heads,blocks,skirted runs good in 12000lb farm stock.My personal puller is 504lp turbo at about 400hp in the 12000lb farm stock class.Rich
  9. R

    1850 gas

    I been using a 1850 gasser with 3speed for round baling about 3yrs now. Does not drink as much gas as our G1000 Vista did diesel.Rich
  10. R

    Past and present 770 owners

    We have and still use 3 770's diesel and gas.
  11. R

    G900 Ring /Pinion

    Thanks,got it will be in touch with you. Have found a pinion.But still interested in your parts.Thanks,Rich
  12. R

    needed

    Don,would like to get a hold of you on 900 parts.Thanks,rich
  13. R

    needed

    I'm looking for a ring and pinion for late model G900. Thanks,Rich
  14. R

    Moline roll bar

    Would be interested,if it would fit 1050.
  15. R

    M670 engine problems

    What type of carb.,vaporizer do you have? When say vapor out of air cleaner do you mean out of top pre cleaner?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top