-
R
still no spark on 641 after getting wrong coil
still no spark on 641 after orielys gave me wrong coil broke neg post off old coil to repair oil hole to cam oil pass leaking.points burnt replaced with $18,00 points and condeser still no spark new al437 plugs insulator to dissy ok.any other things that this wrong coil could have burnt up i... -
R
1960 641 want to go back to starter buton
Thanks john in la that is what im going to do Thanks -
R
1960 641 want to go back to starter buton
It is a 3 wire alternator and newer starter relay smaller with 2 smaller pole one on left facing runs back to keyed switch other one is open. electricial trouble shooting is always been my short suit.the gentleman that i got this from rewirwed this and looks like there is no terminal block only... -
R
1960 641 want to go back to starter buton
also checked button switch with ohm meter looks ok -
R
1960 641 want to go back to starter buton
Just got done rebuilding my 641 new motor rebuild clutch the works but now i would like to get rid of key starter that was put on here do to safty issues i dont like the fact it can be started in gear.not good learned the hard way grandson got on tractor and got put in gear my fault for not... -
R
price difference on pump for here verses orielys
D1NL6600A) price here 140.00 oreilys price 59.95 melling pump talk about price markup -
R
oil pump replacement D1NL6600A retro fit on 641
i have this pump on my 1960 641 info shows this to be 100 psi pump oil pressure should be @45-50 down the line this pump was installed.dont want to change any oil lines or oil gauge will this hurt motor old pump is shot. doing motor rebuild. -
R
changing tranny input shaft seal on 641
any unforeseen problems in changing inut shaft seal remove throw out bearing remove four bolts remove seal replace seal and gasket -
R
how to change input seal on 641
yes tanny seal im changing clutch anl ooked on forum and all said to replace tranny input shaft seal while your in there -
R
how to change input seal on 641
how do you change inpui seal. take off four bolts and replace seal or is there any other problems do i get into -
R
1960 641 134 ci priming oil system after rebuild
Can any one tell me the best way to prime oil system after complete rebuild.new crank,cam.oil pump,pistons,sleeves,head job,mo monet mo money lol -
R
head gasket
Rebuilding 1060 641 134 ci motor rebuild kit came with metal head gasket.what kind of gasket sealer should i use for this.also rolled up edge around cylinders up or down or does this only goes one way? -
R
knock on start up
When oil pressure comes up its 62 psi and stays there all day.if i shut it off after warming up the knock is gone
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy