(800) 853-2651
SHOP NOW

Recent content by RudyM

Yesterday's Tractor Forums
  1. T

    Welp like i figured

    Today was a bit much , I was up before six for qa run to the little shack out back and was no sense tryen to get in and hour more . So war Dept and i had breakfast , did the morning things and left the house a little after 9 . Stopped and filled the tank and were off allowing some extra travel...
  2. A

    hydraulics

    hi, just replaced a clutch and an input transmission shaft on my oliver 1600. afterwards the hydraulics are a lot slower than they were before so much so I have to stop and lift the harrow before making a turn. I also need to have high rpms to make it work at all. there is a new filter and...
  3. R

    JD 4400 Front Axle Rear Seal

    Good day all. New to me 2001 4400, just going over everything to see what needs attention. Found that it marks it's territory under the front end. I know it's fairly common to have leaks around the wheels, and that's not where my leak is. It's the rear seal inside the trunion area where the...
  4. R

    Magneto parts supplier in Canada?

    I have not. I checked my spam bin too.
  5. R

    Magneto parts supplier in Canada?

    Looking to get the D going again, and need to get some parts for the Wico mag. Not that I have anything against the usual suppliers in the US, but would rather find someone that doesn't have to ship international and incur customs charges into the great white north. A quick Google search didn't...
  6. R

    John Deere 40C starter relay installation

    Instead of throwing good money after bad, lets try to understand whats happening... Your system is designed for 6 volts. You are now running 12 volts. The resistance of the starter (the "load") hasn't changed. To get an accurate calculation, use your multimeter and measure the resistance from...
  7. R

    Finding grandpas D

    They're both in good condition! When I got mine from my grandfather, it was in worse shape than they are. Shouldn't take too much to get it shiny again.
  8. R

    Gator Diesel 6x4 siezed

    Sometimes you can find a reefer with a Yanmar in it. I put a Thermoking (engines made by Yanmar) in an 8x8 Argo I have. Only paid $500 for the whole reefer, and made that back in scrap for all the aluminum and stainless. Try to find one that is the same block and all. The TK part numbers are...
  9. R

    JD M belt pulley

    Thanks James. Good to know.
  10. R

    JD M belt pulley

    Thanks Russ. Good thing my lathe is almost ready to start making chips then. I get all the free shafting I can pull out of the scrap bin at work. I'm sure I can come up with something.
  11. R

    JD M belt pulley

    Not too far off of this...
  12. R

    JD M belt pulley

    It's basically like a Woods belly mower. Not a real heavy load, and I plan to put as big of a pulley on as I can. Likely a B belt, possibly doubt B, but I think I can get away with a single. That's what Woods uses. Will be slightly more than 50% wrap on the pulley, so lots of contact area...
  13. R

    JD M belt pulley

    Just a quick question. Has anyone ever changed out the flat belt pulley for a V belt pulley on an M? I seem to remember seeing something to that effect a while back, but can't find anything in all my searching. Haven't pulled mine apart yet (buried in the back shed for the winter while the 3...
  14. R

    JD M hydraulics

    Still wondering. What is the difference between the two piece and three piece? What functionality is different? I would assume that the 3 piece is better for some reason.
  15. R

    JD M hydraulics

    Checked my pump just now. It's a 3 piece. [/img]
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top