(800) 853-2651
SHOP NOW

Recent content by rusty iron

Yesterday's Tractor Forums
  1. rusty6

    Warmed Up to 30F

    At a high of 30 degrees yesterday was the warmest day in over a week so I took advantage of it. Pumped the summer diesel out of two tractor tanks and mixed in some fuel thinner/cetane booster so the fuel will flow this winter. The CIH Magnum I just filled up with summmer diesel as I don't plan...
  2. Kent2255

    1850 diesel

    I just acquired an 1850 diesel that has set for a number of years. I bought it for the fenders and the front wheels to use as upgrades on a couple of my other tractors. I got it running today. It starts and runs really well, even charges! It does have the typical flutter at higher RPMs...
  3. N

    oil leak

    I have a CASE D tractor with a high amount of oil leak. Between crankshaft and the flywheel. Also there is no oil seal on the rear of the crankshaft . The bell housing is one part of the engine block ( no gasket ) is anyone can think of what can be the reason for that?
  4. N

    Lacing wire

    The shop that did my engine rebuild did not lace the main bearing bolts. What is the right wire to use for this? Thanks
  5. S

    Re: Ford 2000 (4 cylinder) with Select-O-Speed

    A NAA transmission is different than a 6/8X1 transmission. I have nothing against a SoS but would rather have 4 or 5 speed in that application .
  6. I

    Farmall c with 404 engine issues

    I have my Grandfathers 1951 Farmall c, the engine in it when I got it was a c123 with a bad head, I replaced it with a c135 from a 404 so I could pull my mower. The c135 runs at 2,300 rpms the original c113 ran at 1,875 rpms so I wanted to run the c135 at about 2,100 to not get too far above the...
  7. D

    Noble sidedressing boxes/motors

    I am trying to understand the electrical wiring behind them as i have no literature and can't find anything online Theres 5 terminals, a red and green that connects to the motor from the junction/terminal and then the other three that are lettered H L and (another) R. I am thinking this...
  8. S

    JD S240 mower deck quit. 99 hrs on the clock

    My JD S240 mower deck shut off while I was cutting grass. I parked it and shut it off. I tried to re start it. Nothing happened when I turned the key. I put a battery charger on it. It indicated 12.9 volts and 92% charge. I have unplugged the seat switch. I turned the key to the on position. My...
  9. T

    Farmall H backfiring

    I have owned my Farmall H for around five years. It was re- done before I bought it. Recently it started to backfire and shut off. It would restart but randomly do this. Progressively it got worse where it doesnt restart very easily. I am in the process of cleaning the carb. The fuel line and...
  10. chuck machinist

    Kow Farmer, Kurt

    Kurt, my email is open give me a ring. Chuck Machinist.
  11. F

    8N top steering linkage question

    I had to disconnect my steering linkage today from the steering arms. I didn't make a note of the alignment. How should the steering arms be aligned with wheels straight? Thanks.
  12. D

    Deere R value?

    Have a neighbor retiring & wants to sell me his R. hasn't ran in 5 or so years, has good rubber & is fairly straight. Looking for a starting point on value. Thanks!
  13. 13fx

    Just putting the VAC back together and Then...

    Just finished bolting the two halves back together and went to adjust the clutch linkage...... Aww bad words more bad words... It's break time.
  14. B

    starter switch for TO30

    looking for gear shift operated starter switch for 1953 TO30. looked about everywhere and can't seem to locate one or even get ideas as where to look? hoping someone reading this might have an idea? don' want to put a push button switch on it,just would not be wright!
  15. T

    Massey Harris 33 Distributor

    I recently purchased a 33 Massey with a late production serial number. I notice it has a Delco distributor on it. Is this common to the 33 or is this something someone cobbled on? Tractor runs fine with it, but I am used to Masseys having autolite ignition components. Thanks for any insight.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top