(800) 853-2651
SHOP NOW

Recent content by RWD

Yesterday's Tractor Forums
  1. C

    Continental engines info

    I have an older Martin Manufacturing Generator with a Continental B427 engine. I am trying to locate a source for parts for this engine. It is a Martin Manufacturing Model MCG60-3. The engine is a Continental B426, Spec. 2226, Engine # 10655. Can anyone help me please. Thank you. Ken
  2. R

    Vicker Vane Pump

    Is the relief valve part of the pump, and are parts available?
  3. R

    Vicker Vane Pump

    I have a 48 8n with a front loader. It has a Vicker Vane Pump on the front shaft. It was working great! Now it doesn't make fluid pressure. I would like to replace it. Anybody know where I can get a new pump???
  4. R

    changing transmission fluid ford 8n

    I want to change the transmission fluid in my 1948 Ford 8n and the bools leave me a bit confused. Can anyone walk me thru it and let me know if as the book states, does it really take 20 qts? Tanks
  5. R

    12 volt vs. 6 volt

    I bought a 1948 8n that has a 12 volt battery. Can I assume that the coil is a 12 volt coil?
  6. R

    Replacing distributor cap ford 8n

    Thanks, I wasn't sure if the offset tang (which I didn't understand) governed the rotor shaft or the position of the dist. body. rwd
  7. R

    Replacing distributor cap ford 8n

    Don't get fiesty. If I understood what an offset tang was it wouldn't sound like greek to me. Anyway I'll go on reading your replies as long as they are helpful. tanks
  8. R

    Replacing distributor cap ford 8n

    Never had the dist. off before. Your directions say to remove the cap before removing the dist. After removing the clamps can I pry the cap off? If I remove the dist. replace the gasket, cap and rotor will the rotor automatically be pointed in the right direction or can the dist, mount with...
  9. R

    Replacing distributor cap ford 8n

    I broke the cap while replacing the altenator. Problem 1 solved. Can I just take off the cap, distributor still attached to engine, and replace the cap and rotor?? The cap seems well attached and I figure that using a srew driver to get the cap off will disturb the gasket above. The...
  10. R

    Replacing distributor cap ford 8n

    I have a cracked distributor cap. It is a front mount distributor on a 1948 ford 8n. My access and visiblity are very much diminished by a front loader. If I pull the distributor as has been suggested, and redo points, condensor, cap and rotor, how do I re-set the timing? The distributor...
  11. R

    Replacing distributor cap ford 8n

    I have a cracked distributor cap. It is a front mount distributor on a 1948 ford 8n. I've released the clamps and wires, but the cap doesn't lift off easily. I'm also confused as the cap shares a gasket with the ignition coil assembly, and the terminal housing. What is the proper method to...
  12. R

    Rear Wheel Bolts for Weights

    I have a 1948 8n. I also have 6 -100 pound weights which can be mounted on the inside of the rear wheel rims. The holes in the weights line up with the Rear Wheel Bolts - 5/8" - 18 x 2-3/4" Carriage Head/ Center Disc To Rim - Uses 5/8" Fine Thread. What I can"t seem to find are bolts that are...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top