(800) 853-2651
SHOP NOW

Recent content by ryanwheelock

Yesterday's Tractor Forums
  1. R

    farmall h nose cone

    Gary I sent a reply to your email. I live a few hundred miles away from any salvage yards and have been looking on craigslist for a few weeks with no luck. I'm willing to pay the shipping even if its a good chunk of $$.
  2. R

    farmall h nose cone

    Just sent that info Thanks Ryan
  3. R

    farmall h nose cone

    Gary I'll take it. I'll pay for shipping on it. Whats your zip code so I can try and figure out the shipping cost. I'm in Cheboygan Michigan 49721.
  4. R

    farmall h nose cone

    No salvage yards for a few hundred miles in my neck of the woods.
  5. R

    farmall h nose cone

    Anyone have a used farmall h nose cone? Don't care if its rusty or painted. Mines beyond repairing.
  6. R

    IH 46 baler, sharpening twine knives

    I ordered an operators manual being I only have the parts manual but my question is can the twine knives be sharpened on the baler or do they need to be taken off on an IH 46 square baler? they still cut but I've been using it for years and never sharpened them. Any other manuals for this...
  7. R

    IH 46 baler needle brake problem

    it drops back down.
  8. R

    IH 46 baler needle brake problem

    Was out baling last night with a IH 46 baler and at the end of the night the needles started cycling non stop. Was getting dark so didn't look it over real close yet but was wondering what would cause the needles to cycle over and over causing the bill hooks to ball up with knot after knot. I...
  9. R

    Oliver 2 bottom plow rim

    Ya that's my last resort, Did it before on other odd balls. cant believe cant find a new or used rim with that bolt pattern.
  10. R

    Oliver 2 bottom plow rim

    I have an Oliver 2 bottom roster comb lift plow that I restored years and years ago but has been sitting for a lot of years. Went to move it and the one rim is rusted beyond repair. Need to find a new or used rim for it but having a hard time locating one. It is a 6 lug with a 5" lug spacing...
  11. R

    Welding/ building up a sprocket on spreader?

    I haven't looked that close at it yet. It was last summer when it started slipping so I parked it and used a diff spreader. Time to start moving manure soon here so want to have that one back up and running. Either way I know how to weld both cast and machined steel. Just wondered if its worth...
  12. R

    Welding/ building up a sprocket on spreader?

    Its the sprocket that runs off the axle to turn the chain.
  13. R

    JD 40 noise in trans?

    1st thing they did was check those fluids and both were up.
  14. R

    Welding/ building up a sprocket on spreader?

    Have any of you guys welded/ built up the teeth on a sprocket before? I have a old IH 200 spreader that the chain is starting to skip a bit on the main sprocket. I'm thinking of building the teeth up a bit my on welder instead of hunting down a new one. Have had a hard time finding parts in my...
  15. R

    Feeding round-up ready corn stalks

    Thinking my dad saw something on tv talking about how GMO stuff will kill you or something. Like you guys said just about all livestock is feed corn that is round-up ready weather it be shelled corn, ear corn, silage or corn stalk bales. I'm not to worried about it. Might just have to keep a...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top