(800) 853-2651
SHOP NOW

Recent content by Sawburner

Yesterday's Tractor Forums
  1. S

    Jubilee 3 point working off FEL pump

    I was mistaken there are three compartments and I did switch the caps.
  2. S

    Jubilee 3 point working off FEL pump

    There is no separation between the rear and the reservoir on a Jubilee. Mark
  3. S

    Jubilee 3 point working off FEL pump

    Yes return from the valve. Mark
  4. S

    Jubilee 3 point working off FEL pump

    I hooked up my 3 point to the FEL pump rather then rebuild the vane pump which may or may not work. I had to get a new valve to have power beyond to run the 3 point. It will now lift my back blade. Mark
  5. S

    Bought another prehistoric piece of junk today.

    Check this web site out its all about vintage machines. http://vintagemachinery.org/ Mark Untitled URL Link
  6. S

    hydraulic gurus? using a FEL pump to power the lift arms?

    I was figuring I would need to use the tractor sump. Was thinking the same as you said about hooking every thing up. Did not think about the GPM and was wonder about the size of the sump. I am going to try it and will post on here how I make out. I was planing on making a plate to cover the pump...
  7. S

    hydraulic gurus? using a FEL pump to power the lift arms?

    I have a Jubilee with a vane pump that is not making adequate pressure to lift the arms. I have a FEL pump that runs off the front of the engine. I am thinking of making an adapter to hook into the hard line where it bolts to the vane pump and run hydraulic lines to the FEL valve. Will it work...
  8. S

    Update Re: Jubilee three point hydraulics

    OK. I misunderstood sorry. I see somebody dressed the side plates and replaced the rotor and that worked for them. I think i will dress my side plates and see how that goes. Then decide after that to buy a rotor. Mark
  9. S

    Update Re: Jubilee three point hydraulics

    I can see as TheOldHokie said that a new vane will fix it. It should say NOT fix it.
  10. S

    Update Re: Jubilee three point hydraulics

    Ok so I tested the pump pressure and I get 500 pounds. I tested it by blocking off the pressure tube where it comes up out of the center section. Took the pump apart and one side plate had some light scuffing the other side looked good. What are my options? I can see as TheOldHokie said that a...
  11. S

    5ft Howse Rotary cutter question

    I have a Howse Rotary cutter too. Call or email Howse they will know just what bolt you need. I needed a fly wheel for mine I called them and they knew just what one I needed. I don't have a model number or any thing. Mark
  12. S

    Jubilee three point hydraulics

    My Jubilee has been sitting for a few days. I needed to move a couple of implements. Hooked to my York rake ( its heavy )and it picked it up first try. Then I had to move my 5 foot Howse rotary cutter it picked it up easy. So what is going on? A confused Mark
  13. S

    Howse Bush hog

    I have a 5 foot Howse cutter and needed a fly wheel for mine and I dont know the model number they just needed the spline count on the shaft. I would contact them and I am sure they can get you what you need.
  14. S

    Jubilee three point hydraulics

    Ok. I can do that. I did it with out blocking it to make sure it was pumping and it mad a bit of a mess. Thanks that is most helpful Mark
  15. S

    Jubilee three point hydraulics

    I will be adding a pressure gauge to my collection of tools.. Thanks Mark
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top