(800) 853-2651
SHOP NOW

Recent content by SJL

Our Phone System is Down!

Please use the Contact us Form

We are working to resolve the issue ASAP! Thanks for your patience!

  1. S

    Davis 210 Backhoe

    Just picked up a Davis 210 backhoe on a Minneapolis Moline 335. Since most Davis equipment appears to be associated with Massey tractors, Im posting here with questions. This has the Davis 102 loader frame on it, presumably for some counterweight and the hydraulic reservoir. It appears to...
  2. S

    Aluminum Radiators

    Has anyone tried the all-aluminum welded radiators that are offered for some tractors? Any opinions? Thanks!
  3. S

    Detroit Tractor

    Just rescued this one from an impending trip to the scrapyard. Have seen some information on Detroit Tractors, but not much. All has been for an earlier version with an aluminum or steel hood. This one is all fiberglass, including the fuel tank. As I understand it, these were available in an...
  4. S

    Behlen Road Gear in Early Unstyled AR

    Can a Behlen road gear be used in an early (1936) unstyled AR?
  5. S

    Tractor Won't Restart

    This morning, my Case VA started right up at about 25 degrees outside. Had about three inches of frost above the carburetor for the entire time that it was running. Ran it for about 15-20 minutes and shut it off. Tried to start it about 1/2 hour later, and it wouldn't start. Occasionally it...
  6. S

    Tractor Won't Restart

    Thanks for the thought on the distributor. Havent ever really had any problems with that in past years, which makes me think that it is something fuel-related. This is my snow removal, brush clearing, and stuck vehicle removing tractor, so it isnt started just for the sake of starting it.
  7. S

    Tractor Won't Restart

    Still have one of those, just don't have it running now. Looking to expand a little on the Oliver collection (70 or 80 Standard, 90 or 99 4 cylinder) That 70 ices up even worse.
  8. S

    Tractor Won't Restart

    Makes sense considering what it did earlier this winter. It wouldn't restart until the temperature got above freezing again. That time, it was several days. As long as you don't shut it off, it will stay running. Now I'm wondering if the gas had some water in it, or maybe just from...
  9. S

    John Deere 314 sight glass and filter

    Like wore out said, the filter has a small hole in it to act as a vent. Needs to have the hole to allow the air to leave the tube and show the correct level of fluid in the transaxle.
  10. S

    IHC/McCormick #80 Wagon Gear

    I recently purchased what I believe is an IHC/McCormick #80 wagon gear. Can anyone tell me how the large rectangular hole in the top and the three holes in the front and rear of the rear bolster upright are used to attach the wagon rack? Am I missing some parts? Thanks!
  11. S

    Wagner Loader Hydraulic Pump Drive Parts

    I'm getting ready to put a Wagner loader on my Case VA, and was wondering if there might be a parts source for the rubber bushings and pins for the hydraulic pump drive, short of having them made at a machine shop. Bushings are probably a fairy common item. These are just a little bit worn...
  12. S

    Wagner Loader Hydraulic Pump Drive Parts

    I'm getting ready to put a Wagner loader on my Case VA, and was wondering if there might be a parts source for the rubber bushings and pins for the hydraulic pump drive, short of having them made at a machine shop. Bushings are probably a fairy common item. These are just a little bit worn...
  13. S

    Wagner Loader Pump Drive Parts

    I'm getting ready to put a Wagner loader on my VA, and was wondering if there might be a parts source for the rubber bushings and pins for the hydraulic pump drive, short of having them made at a machine shop. Bushings are probably a fairy common item. These are just a little bit worn. Bushings...
  14. S

    70 Row Crop Steering Gearbox vs 70 Standard

    Is the worm gear for a 70 Row Crop cut the opposite direction of a 70 Standard? When you turn the steering wheel to the right on a 70 Standard, does the steering arm move forward or backward? Thanks!
  15. S

    Oliver 70 Aftermarket Wide Front

    If it's a one of a kind, it was done by a very good welder. I have to think that the gears at the top of the spindles had some function. Haven't been able to find the information you mentioned regarding Innes. Had no idea they made anything like a tractor front end.
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top