(800) 853-2651
SHOP NOW

Recent content by Smokeonthewater

Yesterday's Tractor Forums
  1. S

    Case 530 CK questions...

    Well I had to remove a little off the underside of the new wheel but otherwise it's perfect and being 2" smaller is wonderful
  2. S

    Case 530 CK questions...

    Wish me luck... my steering wheel burned me up for the last time... Angle grinder, chisel, and hammer and it's GONE! ordered the one above, hope it fits
  3. S

    Case 530 CK questions...

    I'm thinking this steering wheel may work... gonna try to get my old one off to measure and count splines...
  4. S

    Case 530 CK questions...

    Well I would sell it IF I come up w a good turnaround seat system that works for me Unfortunately mine will have to sit outside because I dont have indoor space available for it tho I have been trying to peice together a 16x40 tractor shed but still lack materials to finish it
  5. S

    Case 530 CK questions...

    Thanks guys
  6. S

    Case 530 CK questions...

    I just drug home a new to me 1963 530 CK... Will have several questions... It is a dry clutch shuttle shift trans and I haven't had any luck looking up fluid capacities... Brakes sorta work a little and po said he replaced them so I suspect oil contamination... is that possible...
  7. S

    Case 530 CK questions...

    This post was edited by Smokeonthewater on 05/05/2023 at 08:26 pm.
  8. S

    I'm an idiot...connected jumper cables backwards

  9. S

    I'm an idiot...connected jumper cables backwards

    Those lower brackets are junk... crappy design.... If you look in my build thread "$1500" you can see where I modified that bracket for a MUCH better fit.
  10. S

    Water Ballast removal

    If you do as above, then take the wheels off the tractor, inflate, lay on ground, valve down, repeat, you will get nearly all water out...
  11. S

    where should I attatch the hoist to my motor?

    If you want to get fancy....
  12. S

    top link length recommendations

    Sounds like a non issue to me
  13. S

    Replacing PTO shaft

    I wouldn't, I would use my forklift to pick the back of the tractor up enough to do the job and then block it there with the wood cribbing I keep on hand. Every time I drive down the hill to my backyard I'm tilting further than that, for longer than it takes to swap shafts assuming it isn't stuck...
  14. S

    Replacing PTO shaft

    After you back up onto those 6x6's, take the front wheels off and set the hubs on the ground.. Plan to work reasonably fast so as little oil as possible runs past your transmission input seal
  15. S

    Ford 8N High & Low Gear

    I hope you're not running the tractor with that spring on there. Probably a real good way to wear out your shift fork
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top