(800) 853-2651
SHOP NOW

Recent content by Sneakymedic

Yesterday's Tractor Forums
  1. S

    IH 560D Air intake question

    Sounds like the plan I was going to follow unless anyone came in with something that they felt was worth making. The head is at a good shop getting worked over. Thanks for the reply!
  2. S

    IH 560D Air intake question

    Well, THAT should let it breathe!!! That is some neat engineering!
  3. S

    IH 560D Air intake question

    yes, I know I need to do something, but jsut not sure where to start. figured I wouldnt reinvent the wheel if someone had already done any mods. I do think that the engine would breathe better if I could avoid the long breather and through the air cleaner....but it has always worked well for 60...
  4. S

    IH 560D Air intake question

    Has anyone done anything special to your air intake on your 560d puller? I am doing a inframe rebuild, and was looking at the intake. It doesnt seem to make much sense to do much of a port and polish on the head, with the way that intake is made. You cant hardly polish/ clean up any internals...
  5. S

    Farmall 460

    I dont mean to hijack the thread, but it seemed to be in the same topic. So will the front covers that it(301) is currently wearing, even in a 856 still work to mount it in a 460? I guess I should have been more clear
  6. S

    Farmall 460

    With a 301 in a 460 swap?.. would the 460 282 Diesel front and rear plates bolt on a 301 gas engine for the swap? Thanks. Mike.
  7. S

    49ish 8n Starting issue

    "Fun" is the first three letters in funeral. :) They are simple machines, I wish I knew more about electrical issues. I took a welding course evenings over the summer, I need to take an electrical course. And a CAD drawing course, and a Machining course, and a…. hahahahahaha.
  8. S

    49ish 8n Starting issue

    ok, so this evening after work, I went outside and piddled. I did hook the starter thumb switch up and that didn't work. I assume that is broken. What I did first was to take the starter off. There was a lot of grime, wire wheeled the tranny frame and the starter face. She turned over like a...
  9. S

    49ish 8n Starting issue

    yep. thats what I did. (thumbs up)
  10. S

    49ish 8n Starting issue

    Did the youtube thing for the quick multimeter tutorial. 12.49v
  11. S

    49ish 8n Starting issue

    So I have borrowed a voltmeter from a friend. What do I set the voltmeter on to test volts from a battery? And there are three locations for the wires to plug in the voltmeter. Any clue on which two of the three I should plug it in on the VM? I did hook a battery charger up to it to assure it...
  12. S

    49ish 8n Starting issue

    I have a three pole solenoid currently. Hot on the right from batt, hooked to starter on left with copper bar, small post hooked to "st" on middle of key switch.
  13. S

    49ish 8n Starting issue

    The one thing I have not done is to take the starter loose and wirebrush the contact between the starter and the transmission casing. This tractor has been outside for a few months due to a project in the barn. It could have gotten some rust between the two. I will try this tomorrow night. I...
  14. S

    49ish 8n Starting issue

    So today I took the JFOR schematics and gave mine a once over. I found a few things and fixed them. Thanks for that link and advice. It was helpful. I also cleaned the starter and the solenoid faces for a better ground. So this tractor cranked and started before, it has me stumped. I did buy...
  15. S

    49ish 8n Starting issue

    found the diagrams. Im going to work on it tomorrow?.I will advise what I find.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top