(800) 853-2651
SHOP NOW

Recent content by steve terplak

Yesterday's Tractor Forums
  1. S

    Massey 1359 discbine- looking used

    decided it is time to retire the NH 479 haybine. Bought new in 1975, cut hay here ever since. Looking for a used 9’ discbine that we can run with multiple machines - been looking at models based off the 5209. Found a lightly used 1359 for sale locally, going to look in a couple days...
  2. S

    Massey 265 PTO stops under load

    Massey 265 with IPTO. Got it out for spring Rototilling of a very small garden. As soon as till dug below 3”, it would stop turning. While PtO shaft. Tractor kept humming. Didn’t show any sign of strain. Lift it up, starts spinning again. Turns on and off fine with minimal load, just under...
  3. S

    NH 273 Needle Return Question

    Just wanted to follow up on this since our problem appears to be solved. Went out, cleaned everything up, tightened up knotter brake. Noticed that the bolt which mounts that brake-side of the knotter stack to the frame had completely broken off, so it was being held at only one point instead so...
  4. S

    NH 273 Needle Return Question

    I appreciate the quick responses. My gut was telling me brake and, thinking back, when trying to find our initial problem, I may have grabbed the brake disc with a greasy glove So, my plan tomorrow, is the hit the disc with some brake kleen., pull the assembly apart and clean crap out of it and...
  5. S

    NH 273 Needle Return Question

    Finished baling for the day a couple days ago and noticed that my knotters didnt look right when blowing chaff off. Looked in more detail, twine had hung up in the bale hook and twine fingers didnt look right. Spring which holds the lever in place had broke. Had a spare in the toolbox, went to...
  6. S

    Oil Cooler 165

    I have the service/repair manual downloadedFrom what I can find this isn’t covered. I have a cheaper, less detailed service paper repair manual that covers multiple models. I am going to check that. Hopefully problem will be solved. Hate when stuff goes awry in the winter. Actually...
  7. S

    Oil Cooler 165

    Jim, Thank you for the info. I assume that this filter is prior to the cooler in front of the radiator? Fluid is pushed through and not suction? Is this the sole filter for the hydraulic system? Or is this only for the multi power system? Or none of the above? Thanks again. I went out...
  8. S

    Oil Cooler 165

    Need some help with a Massey 165. Continental gas with Multi Power. Was out plowing (backblading) snow and smelled some trans hydraulic fluid. Got off tractor and there appeared to be hydraulic fluid leaking out of the radiator (?!). Turns out it was the oil cooler in front of the radiator...
  9. S

    I got the new to us White 598 plow in the field today.

    You pick that up at Jim’s last auction? Or buy it off the lot. I feel like that plow went pretty cheap at the Sept. auction.
  10. S

    Troubleshooting steps for no start

    Had a no start condition with our Massey 265 a few weeks ago. I though we were having neutral switch issues...seemed to make the most sense...still couldn’t figure it out... Found out there was a small fuse under a cover on the dash...it was broken. Problem solved.
  11. S

    Ratchet/ Socket- Sears not Craftsman

    Sorry. I intended to post this in Tool Talk. I will leave it instead of re posting.
  12. S

    Ratchet/ Socket- Sears not Craftsman

    Cleaning out a family friends’ basement for her. I get tools and scrap wood, she is no longer paying someone to take her father’s old tools etc. It is a good trade. Got a nice set of 1/2” S&K tools. 42470 ratchet. Some no name Taiwan stuff. There is another set marked Sears but not...
  13. S

    NH Knotter Question.

    That is the mystery. Still not sure what happened. Broke first shear bolt of the season (flywheel). Heard tremendous bang. Needles were up. Right knotter’s pin and clip Which hold knotter in position were MIA. Our guess: pin fell out, knotter dropped out of position, threw it out of...
  14. S

    NH Knotter Question.

    Baler question. Older New Holland. 311. Sheared the pin that holds the twine disc shaft onto the pinion gear. Knotter manual refers to it as a “grooved pin”. But parts diagram does not list it. It is #15 and 16 in diagram, no pin listed. Why is it a “grooved pin”? From what I can tell...
  15. S

    Cut some hay

    I thought you purchased a 488 haybine earlier in the spring? Not working?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top