(800) 853-2651
SHOP NOW

Recent content by steve zaragoza

Yesterday's Tractor Forums
  1. J

    david brown 880

    I have a David brown 880 basket case I'm sure not all there I got it in a deal with other tractors. The head is off one piston is gone I do not have oil pan it is a red tractor. I guess what I'm wondering is if it has any value other than scrap hate to scrap it if some one could use it. Located...
  2. A

    135 carb problems still baffeled

    engine run for a couple mins then runs out of gas.wait 15or 20 sec fires right back up runs a couple mins cuts off again. there is no blockage anywhere believe me ive checked everything about 20 times now and taken the carb apart the same, nothing in the tank,or bowl, i even make a new...
  3. O

    1370 puller

    I was looking at some older posts and came accross a 1370 puller with the name of " Evans Eagle". Does anyone know anything about this tractor?
  4. 8

    Question for Farmers that Lease Ag Land

    Buddy of mine put a 40 up for sale about 3 years ago....had a verbal agreement year to year with next door neighbor to farm it. The land was recently sold and the new owner will not let this "leasing" farmer on it this Spring. The farmer is upset with the seller and is threatening to sic his...
  5. H

    Impco regulator problems on 450 LP

    I know that the Impco regulator/vaporizor isn't factory for my 450 LP, but it's all I've got. Can anybody clue me in about servicing it without taking it apart? (and thus ruining the diaphrams). It apparently has an intermittent restriction on the fuel inlet side, because it will run really...
  6. T

    anybody ever set an EZ-Flow drop spreader for buckwheat?

    It's not on the chart. Before I go through all the calibration procedure for 40 lbs. per acre of buckwheat through my EZ-Flow 100, has anybody already figured it out?
  7. M

    65 4000 Hydraulic fluid

    Where do I put the hyrdo fluid in, is the rear and hydro common. Where is the level plug. 65 4000 gas.
  8. T

    Gene Wedde

    Just finished a transaction with Gene, He responded promptly to every email, was very professional, and shipped Item quickly, obviously wanted to make sure I was satisfied with my purchase, a true asset to our community.
  9. B

    NAA Bolster Pin No Go

    I am working on my NAA trying to get the new bolster pin to seat correctly.I have an 1/16 gap all the way around the pin where it won"t seat up next to the bolster.The original pin seats perfect.The pin fits tightly,but cannot get it to go in the extra little bit right up next to the front of...
  10. C

    135 Power Steering info

    Hi I need some info I have a 135 5000 hr and looking to trade for 135 with low hours dealer told me it had a double cylendar power steering I never had power steering before looked with some that did have most of then leaked but is the double cylendar good or not.Tried a 150 with power it seemed...
  11. B

    8N hydraulic pump

    Where could I get a hydraulic pump for an 8N, the front hydraulic pump that fits on the crankshaft. My son and I are restoring 2 8Ns right now. A "52 8N that my father bought new and I have given to my son, and a "49 that my uncle bought new that we are fixing up for my son-in-law, an...
  12. L

    International A Shifting Lever

    The shifting lever on my 1946 International A is worn badly and the gears occasionally jam. Anyone have the dimensions to weld/build up the piece on the end that fits into the runners? The parts manual looks like a small ball on the end, but mine is completely flat with a bit of a taper, so...
  13. C

    Update: 953 or 963 Running Gear

    This message is a reply to an archived post by cjenk88 on November 14, 2009 at 22:02:16. The original subject was "953 or 963 Running Gear". Wagon update. My dad and I finally got around to working on the wagon. Somewhere along this wagons life, someone has repainted it before. When we...
  14. D

    Wire Dia. 12v fm round can conv.

    I need a wiring diagram for a 12 volt fm round can conversion. I've searched the archives and Hobos site. I think I could do it without but I don't want to buy another alt or coil. Thanks. DON TX PS Remember I'm electrically challenged. (%^)
  15. J

    WD serial number

    trying to find a serial number to get a new shifter looks like the one that is in there is a 53 model but very worn and no sure looked on back axle and found two different numbers on each side and a small number on engine block any ideas
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top